This form helps you record what you observe while checking brake pads and related stopping components on bicycles and strollers. It is a practical record-keeping and planning tool only. It does not replace a qualified mechanic's judgement, a manufacturer's instructions, or any local rules that may apply where you live. If anything feels unsafe or unclear, stop using the vehicle and seek hands-on help from a person experienced with that type of brake system.
Tip: work on one vehicle at a time, keep the vehicle stable and supported, and write down what you actually see rather than what you expect to see. Small pad wear differences can change how a brake feels, so it is worth measuring rather than guessing.
I understand this form is for record-keeping and planning, and that observations should be confirmed by a person competent with the relevant brake system before relying on the vehicle.
Is the vehicle currently unsafe to push, ride or push while loaded?
Have you inspected this vehicle with this form before?
Inspector name
Your role for this inspection
Owner or regular user
Parent, guardian or caregiver
Home mechanic
Workshop or shop technician
Fleet or shared-vehicle coordinator
Other
Contact email or preferred contact method
Inspection date
Inspection start time
Inspection location or setting
Conditions during the check
Dry and mild
Dry and cold
Hot or sunny
Damp or humid
Rainy or wet surfaces
Dusty or sandy environment
Indoor workshop
Approximate distance or use counter reading on the vehicle (if available)
Unit used for the reading above
Kilometres
Miles
Trips or outings counted
No counter fitted
Not sure
Vehicle nickname or identifier
Vehicle description
Commuter Bike
Double Baby Stroller
Kid's Pedal Bike
Cargo Bike
Other
Make and model (if known)
Year of manufacture or year acquired
Wheel size or rim diameter
How is the vehicle mainly used?
Short flat trips
Hilly or steep routes
Wet or muddy conditions
Gravel or unpaved paths
Heavy loads or multiple passengers
Mostly indoors or on smooth surfaces
Long descents where brakes stay on for a while
How often is the vehicle used?
Daily
A few times a week
About once a week
Occasional use
Seasonal or rarely used
Where is the vehicle usually stored?
Indoors, dry and warm
Indoors but unheated
Covered outdoor area
Outdoors exposed to weather
Varies
Has the vehicle been dropped, crashed or involved in any impact recently?
Identify the brake system before judging the pads. Different systems wear differently and need different checks, so recording the system first makes the rest of the form much more useful.
Primary brake system on this vehicle
Hydraulic Disc
Mechanical Disc
Rim V-Brake
Other or mixed system
Does the vehicle have brakes on more than one wheel or more than one track?
Pad material currently fitted (mark any that apply)
Resin or organic compound
Semi-metallic compound
Sintered or fully metallic compound
Ceramic or other specialty compound
Not marked or unknown
Mixed compounds front and rear
Disc rotor diameter (if a disc system), in millimetres
Caliper piston count (if known)
Single piston
Twin or dual piston
Four piston
Not sure
Date the pads were last replaced (if known)
Any previous brake work, upgrades or part changes worth remembering?
Complete one row per brake unit or per vehicle you are checking. Use the option wording shown in each column heading so records stay consistent over time. Pad wear is easiest to judge with the pad removed or with a clear side-on view and a small ruler or feeler gauge; if you cannot measure it, choose the closest description and note the uncertainty.
Brake Pad Condition Overview
Vehicle Description (Commuter Bike/Double Baby Stroller/Kid's Pedal Bike/Cargo Bike) | Brake System (Hydraulic Disc/Mechanical Disc/Rim V-Brake) | Lever Travel Squeeze (Firm/Short Travel, Soft/Touches Handlebar, Spongy) | Pad Wear Remaining (🟢 Thick (>3mm), 🟡 Moderate (1-2mm), 🔴 Critical (<1mm/Metal)) | Brake Noise (Silent, High-Pitch Squeal, Grinding Metal) | |
|---|---|---|---|---|---|
Commuter Bike | Hydraulic Disc | Firm/Short Travel | 🟢 Thick (>3mm) | Silent | |
Double Baby Stroller | Mechanical Disc | Soft/Touches Handlebar | 🟡 Moderate (1-2mm) | High-Pitch Squeal | |
Kid's Pedal Bike | Rim V-Brake | Firm/Short Travel | 🟡 Moderate (1-2mm) | Silent | |
Cargo Bike | Hydraulic Disc | Spongy | 🔴 Critical (<1mm/Metal) | Grinding Metal | |
Thinnest pad measurement you recorded, in millimetres
How was the pad thickness judged?
Measured with a ruler or feeler gauge
Estimated by eye against a known reference
Estimated from how the brake feels
Could not access the pad for measurement
Are the pads wearing evenly across their surface?
Is any pad worn down to a metal backing plate or metal contact point?
Lever feel is one of the quickest ways to notice a change in a brake system. Compare both levers if the vehicle has two, and squeeze gently as well as firmly so you can feel where the pad first contacts the rotor or rim.
Please rate each statement about lever feel
Strongly disagree | Disagree | Neutral | Agree | Strongly agree | Not applicable | |
|---|---|---|---|---|---|---|
The lever feels firm and predictable when squeezed slowly | ||||||
The stopping point is consistent squeeze after squeeze | ||||||
The lever returns fully and promptly when released | ||||||
Lever reach is comfortable for the main user's hand size | ||||||
The two levers on this vehicle feel similar to each other |
Overall lever travel before the brake begins to hold
Firm/Short Travel
Soft/Touches Handlebar
Spongy
Feels different on each side
How would you rate the overall firmness of the lever feel?
Does the lever feel change after several repeated squeezes?
Do you notice any air-like softness or a slow sink in the lever on a hydraulic system?
Is there any visible fluid weeping or residue around the lever body, hose or caliper?
Approximate free play before the pads contact, in millimetres (if you measured it)
Predominant brake noise
Silent
High-Pitch Squeal
Grinding Metal
Occasional light tick or rub
Other or hard to describe
Any of these sensations while braking? (mark any that apply)
Pulsing or juddering through the lever
Vibration in the handlebar or grip
Grabby or sudden bite
Brake feels weak or needs a lot of effort
Vehicle pulls to one side when slowing
Wheel keeps turning slightly while the brake is held
None of these
How confident do you feel about the braking performance right now?
Any other sounds, smells or observations during braking?
Pads only work well when the surface they press against is clean, true and not deeply worn. These checks help you tell a pad problem from a surface or alignment problem.
Is the disc rotor or rim braking surface clean and free of obvious oil or polish residue?
Does the rotor or rim run true without visible wobble?
Are there deep grooves, scoring or a noticeable lip on the braking surface?
Is the caliper or brake arm positioned squarely over the rotor or rim?
Do the pads sit flat against the surface rather than at an angle?
Are all mounting bolts, retaining pins and clips present and looking secure?
Condition of hoses, cables and housings (mark any that apply)
Supple and undamaged
Outer housing kinked or flattened
Frayed or rusted inner cable
Rubbing against the wheel or frame
Connections look damp or weeping
Not visible or not applicable
Which actions did you carry out during this session? (mark any that apply)
Wiped pads and braking surfaces with a clean, lint-free cloth
Removed loose grit or debris
Re-centred or re-aligned the caliper or brake arms
Adjusted cable tension or barrel adjuster
Adjusted lever reach or position
Bedded in new or cleaned pads with repeated controlled stops
Replaced pads
Replaced rotor or rim component
None of the above
Did you use any cleaning product on the braking surfaces?
Were any parts replaced during this session?
Describe any adjustments you made and how the brake felt afterwards:
Simple pad wear rate reference: wear per unit of use = (starting thickness minus remaining thickness) divided by distance travelled
The wear rate above is only a rough comparison aid between checks on the same vehicle. It is not a prediction of pad life, because terrain, load, weather, riding style and pad compound all affect how quickly material is used.
Record the parts and materials used or quoted for this vehicle. Line totals are calculated automatically from quantity and unit cost. Enter costs in your own currency; the form does not convert between currencies.
Parts and Materials
Part or Material Description | Fitted or Just Quoted | Quantity | Unit Cost | Line Total | |
|---|---|---|---|---|---|
Disc brake pad pair | Fitted | 1 | $24.50 | $24.50 | |
Rim brake pad set | Quoted | 2 | $9.75 | $19.50 | |
Brake cable and housing | Fitted | 1 | $12.00 | $12.00 | |
$0.00 | |||||
$0.00 | |||||
$0.00 | |||||
$0.00 | |||||
$0.00 | |||||
$0.00 | |||||
$0.00 |
Estimated total cost of outstanding work not yet performed
Are any required parts currently unavailable or on order?
If it is safe to do so, check how the vehicle slows in a controlled, open area with no traffic and a smooth surface. Keep speeds low, avoid sudden swerving, and never test with a passenger or child on board until you are confident in the result. If a test is not practical or safe, skip this section and note why.
Was a controlled stopping check carried out?
How confident were you in the stopping performance during the check?
How predictable was the braking response during the check?
Very unpredictable
Mostly unpredictable
Acceptable
Mostly predictable
Very predictable
Approximate distance travelled from first squeeze to a full stop, in metres (estimate is fine)
Approximate speed at the start of the check (in your preferred unit)
Unit used for the speed estimate above
Kilometres per hour
Miles per hour
Walking pace estimate
Not recorded
Did the vehicle stop in a straight line without pulling to one side?
Would you be comfortable using this vehicle in normal conditions right now?
What follow-up actions are needed? (mark any that apply)
No action needed, continue routine checks
Re-check pad thickness soon
Replace pads
Inspect or replace rotor or rim surface
Have the hydraulic system checked by a competent person
Replace cables or housings
Correct alignment or fastener issues
Keep the vehicle out of use until resolved
Please rank these follow-up priorities for this vehicle, most urgent first
Restore confident stopping power | |
Silence brake noise | |
Even out pad wear | |
Improve lever feel and reach | |
Reduce long-term running cost | |
Keep a tidy maintenance record |
Suggested interval until the next pad check
Within one week
Within one month
Every three months
Every six months
Once a year or at the change of season
Before the next heavy-load or hilly use
Planned date for the next inspection
Planned time for the next inspection (optional)
Would you like a reminder before the next check?
Will anyone else use this vehicle before the next check?
Please rate the current condition of each area below
Pad material remaining | |
Lever feel and reach | |
Noise level during braking | |
Rotor or rim surface condition | |
Cable, hose and fastener condition | |
Overall confidence in stopping power |
Photos and short notes make future comparisons far easier. A side-on photo of the pad and a photo of the whole brake assembly are usually the most useful.
Please upload a photo of the brake pad and braking surface
Please upload a photo of the lever and cable or hose routing
Please upload any supporting documents, such as a parts receipt or a previous inspection sheet
Additional observations, measurements or context worth remembering
I confirm that the observations recorded here reflect what I saw during this session
I understand that brake performance can change with load, weather, surface and wear, and that regular re-checks are sensible
Name of the person completing this record
Please sign to confirm this record
Date the record was completed
Name of a second person who reviewed this record (optional)
How useful was this form for planning your brake maintenance?
Any suggestions for improving this form?