This form is designed to record thickness measurements taken on painted surfaces, metallic coatings, protective films and other industrial surface treatments. It guides you from sample identification through instrument verification, individual readings, statistical summary and an overall compliance evaluation. Complete each section as fully as the job allows and attach supporting evidence where available.
Enter thickness values in a single, consistent unit throughout the form (commonly micrometres, mils or millimetres) and state the unit used. Where a question is marked as required, please answer it before submitting. Note that this template is a general-purpose record and does not replace any measurement procedure, drawing note or specification that applies to your own work.
I confirm that the readings recorded here were taken by me (or under my direct supervision) and reflect what was actually measured on the workpiece.
Have you reviewed the written measurement procedure or work instruction that applies to this job?
Is this measurement being taken as part of a batch sample rather than on every item produced?
Sample ID/Item identifier
Job, order or work reference number
Item or component description
Number of items in the batch or lot
Date of measurement
Time measurement started
Measured by (name)
Department, team or laboratory
Contact email or phone for follow-up
Is this a re-measurement taken after an earlier set of readings?
Stage at which the measurement is being taken
Incoming material or substrate check
Immediately after coating application
After curing, drying or ageing
During production, in-process check
Final inspection before release
After service exposure or field use
Failure investigation or rework assessment
The substrate material and its surface condition strongly influence which measurement principle is suitable and how readings should be interpreted. Please record the material as accurately as known.
Substrate material family
Carbon steel or low-alloy steel
Stainless steel
Aluminium or aluminium alloy
Zinc, galvanised or zinc-alloy base
Copper, brass or bronze
Other non-ferrous metal
Concrete, mortar or cementitious board
Wood or wood-based panel
Plastic, polymer or composite
Glass or ceramic
Other or not certain
Is the substrate magnetic (ferromagnetic)?
Substrate thickness, if relevant to the method used
Surface preparation or condition of the substrate before coating
As-received or mill finish
Abrasive blast cleaned
Mechanically ground, sanded or abraded
Chemically cleaned, degreased or etched
Polished
Coated with a primer or pre-treatment
Surface roughened or profiled
Not known
Approximate surface roughness of the substrate
Smooth (for example polished or finely finished)
Light texture (for example lightly abraded)
Moderate texture (for example typical blast profile)
Coarse texture (for example heavy blast or cast surface)
Roughness not assessed
Geometry of the measurement area
Flat panel or flat plate
Large diameter curve or cylinder
Small diameter curve, tube or wire
Internal surface (bore, pipe inner wall)
Edge, corner or radius area
Complex or irregular shape
Was the substrate verified as being the correct material before measurement began?
Coating or treatment type being measured
Paint or liquid-applied coating
Powder coating
Metallic coating (for example zinc, aluminium, nickel, chrome)
Anodised or converted surface layer
Hot-dip coating
Electroplated or electroless plated layer
Protective film, tape or laminate
Thermal spray coating
Ceramic or high-temperature coating
Liner, sealant or encapsulation layer
Other surface treatment
Number of coating layers or coats applied
Coating colour, finish or batch/lot code
Application method used to apply the coating
Spray (conventional, airless or electrostatic)
Dip or immersion
Roller or brush applied
Electroplating
Hot-dip immersion
Powder spray and cure
Chemical vapour or vapour deposition
Laminating or adhesive bonding
Not known
Has the coating been fully cured, dried or aged before measurement?
Is the coating system multi-layer, with different materials in each layer?
Coating Layer Schedule
Layer No. (1 = nearest substrate) | Layer material or description | Nominal thickness | Colour/code/reference | Measured separately? | |
|---|---|---|---|---|---|
1 | Primer coat | 40 | Grey primer | ||
2 | Topcoat | 80 | RAL 7016 matt | Yes | |
Any special features of the coating system worth noting (for example metallic flake, conductive topcoat, soft or easily deformed layer):
Record the instrument and the measurement principle used so that the readings can be reproduced or reviewed later. Include the instrument identifier exactly as it appears on the equipment register.
Instrument ID/asset number
Instrument make and model
Measurement principle used
Magnetic induction (magnetic substrate, non-magnetic coating)
Magnetic reluctance/magnetic pull-off
Eddy current (non-ferrous metal substrate)
Ultrasonic pulse-echo
X-ray fluorescence or similar spectroscopic method
Cross-section viewed under microscope
Magnetic or mechanical dry-film gauge
Optical or laser based measurement
Other method
Instrument resolution or least count (in the unit used)
Date of last calibration or verification of the instrument
Next calibration or verification due date
Was the instrument checked against reference foils, standards or a certified sample immediately before the measurement?
Was the instrument zeroed or calibrated on an uncoated area of the same substrate before use?
Was the probe or sensor cleaned or checked for damage before measurement?
Operator experience with this instrument
Formally trained and assessed as competent
Trained but not formally assessed
Self-taught or experienced through practice
Using the instrument for the first time
Environmental and surface conditions can shift readings, particularly for sensitive methods. Recording them helps when results are reviewed or compared between days.
Ambient temperature during measurement (°C)
Relative humidity during measurement (%)
Surface temperature of the part, if measured (°C)
Location of the measurement
Indoor workshop or laboratory
Outdoor site or field
Production line while the part is in process
Storage area or warehouse
Other location
Surface condition at the time of measurement
Clean and dry
Dust or light debris present
Damp, wet or condensation present
Oil, grease or residue present
Surface temperature elevated (for example sun or process heat)
Surface irregular, textured or profiled
Accessible without obstruction
Difficult access, at height or in a confined space
How measurement locations were selected
Fixed grid pattern across the surface
Positions marked on a drawing or sketch
Critical or high-wear areas nominated by engineering
Randomly selected positions
Edge, corner and flat area comparison
Locations agreed with the customer or requester
Other approach
Planned number of measurement locations on this part
Number of repeat readings taken at each location
Were locations spaced far enough apart to avoid overlapping readings?
Please upload a photo of the part or surface showing where measurements were taken (optional)
Enter one row per measurement location and record the repeat readings taken at that location. The location average, minimum, maximum, spread and deviation from nominal are calculated automatically. Use one unit consistently across the whole table.
Unit used for all thickness values in this form
Measurement Location Readings and Calculated Values
Location ID | Location description | Reading 1 | Reading 2 | Reading 3 | Location average | Location minimum | Location maximum | Spread (max minus min) | Nominal specified thickness | Deviation from nominal | Within specified range? | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
L1 | Centre of face, panel A | 118 | 121 | 119 | 119.33 | 118 | 121 | 3 | 120 | -0.67 | ||
L2 | Upper edge, 20 mm inboard | 96 | 94 | 97 | 95.67 | 94 | 97 | 3 | 120 | -24.33 | ||
L3 | Lower edge, 20 mm inboard | 122 | 124 | 123 | 123 | 122 | 124 | 2 | 120 | 3 | ||
L4 | Near bracket weld | 145 | 149 | 142 | 145.33 | 142 | 149 | 7 | 120 | 25.33 | ||
L5 | Mid-span, opposite face | 117 | 116 | 118 | 117 | 116 | 118 | 2 | 120 | -3 | ||
Notes on individual readings (for example unusual values, re-tests, surface defects, edge effects):
Were any readings discarded or repeated during the session?
Was an independent re-check of the readings carried out (second instrument, second operator or different method)?
Was the measurement repeated after adjusting probe pressure, couplant or technique?
Summarise the full set of location averages (or all individual readings, depending on your chosen convention — state which one you used). These values are used together with the specified range to reach the compliance result in the next section.
Basis used for the summary statistics
All individual readings entered in the readings table
Location averages only
Final accepted readings only (discarded readings excluded)
Total number of readings included in the summary
Overall average thickness
Minimum thickness recorded
Maximum thickness recorded
Range (maximum minus minimum)
Standard deviation of the readings (if calculated)
Is the variation across the surface considered uniform for this application?
Enter the specified thickness range that applies to this work and compare the measured results with it. If no formal range has been supplied, record that clearly rather than estimating a target.
Source of the specified thickness requirement
Engineering drawing or technical specification
Project or customer requirement document
Internal workmanship standard or guide
Coating product data or technical sheet
Agreed verbally with the requester
No formal specification supplied
Specified minimum thickness (lower limit)
Specified maximum thickness (upper limit)
Nominal or target thickness, if stated
Unit used for the specified range
Micrometres (µm)
Mils (thousandths of an inch)
Millimetres (mm)
Other unit (please state in the notes)
Are all measured values within the specified range?
Overall compliance result
Compliant – within specified range
Compliant with comment (for example within range but near a limit)
Non-compliant – outside specified range
Cannot be determined – specification unclear or data incomplete
Not assessed against a specification
Disposition of the measured item
Accept and release
Accept with a recorded deviation
Rework, re-coat or repair required
Reject
Hold pending further review
Not applicable – measurement on a test panel only
Did you observe any of the following during the measurement?
Blistering, bubbling or lifting of the coating
Cracking, crazing or flaking
Pinholes, voids or bare spots
Runs, sags or heavy build areas
Uneven colour or visible thickness variation
Dust, debris or contamination trapped in the coating
Damage to the coating from handling or the probe
Nothing unusual observed
Likely contributing factor, in your view
Application technique or spray pattern
Curing, drying or ageing conditions
Surface preparation or cleanliness
Coating material mixing, viscosity or batch variation
Part geometry (edges, corners, welds, recesses)
Instrument or measurement technique
Environmental conditions during application
Not known
Please describe any action taken or recommended (for example re-coat area, adjust spray settings, re-train operator, re-measure after cure):
Person or team responsible for the action
Target completion date for the action
Does this result need to be shared with anyone else (for example production, engineering or the requester)?
Attach anything that helps a reviewer understand or repeat the measurement. Files remain with the record and can be referenced later.
Instrument printout, screenshot or data export showing the readings
Photo of the measurement surface close-up (showing coating condition)
Photo of the instrument display at a measurement location
Reference drawing, sketch or specification extract used for the specified range
Calibration certificate or verification record for the instrument used
Are there any further attachments to follow later?
Please rate how confident you are in the recorded data. This helps reviewers decide whether additional checks are worthwhile.
Rate the following statements about this measurement session
Strongly disagree | Disagree | Neutral | Agree | Strongly agree | |
|---|---|---|---|---|---|
The measurement procedure and expected values were clear before starting | |||||
The instrument was in good condition and properly set up | |||||
Measurement locations were representative of the whole surface | |||||
Surface and environmental conditions were suitable for measurement | |||||
The recorded data is complete and free from transcription errors | |||||
The compliance judgement is supported by the data collected |
Overall, how confident are you in these results?
Anything that would make these results more reliable next time (for example more locations, different probe, longer cure time):
Reviewed by (name and role)
Date of review
Outcome of the review
Record and result accepted as submitted
Accepted after clarification or correction
Returned for further measurement
Escalated for technical decision
Reviewer comments or additional observations
I have checked that the readings, summary values and compliance result in this record are consistent with each other.
Signature of the person who carried out the measurement
Signature of the reviewer or approver
Date the record was completed
Record or report reference assigned to this measurement
Analysis for Coating Thickness Measurement Form – Readings, Averages & Compliance Record
Important Note:
This analysis provides strategic insights to help you get the most from your form's submission data for powerful follow-up actions and better outcomes.
AI-Generated Content: This template and its accompanying guidance are AI-generated to provide a practical starting point for your form-building needs. Please review and customise the content to ensure it is accurate, appropriate and suitable for your intended use.
This guide is provided for general informational and planning purposes only. It does not constitute professional, legal, financial, medical, employment, privacy, regulatory, or advice of any other kind, nor does it certify that this template is suitable or compliant for any particular jurisdiction or purpose.
Laws, regulations, industry practices and business requirements vary. You are responsible for reviewing and customising the template to suit your intended use and obtaining advice from appropriately qualified professionals where necessary.
Please delete this section before publishing your form. See our Terms of Service for further information.
This Coating Thickness Measurement Form is a structured, end-to-end record for capturing thickness data on painted surfaces, metallic coatings, protective films and other industrial surface treatments. It moves through a logical sequence: attestation and procedure awareness, sample and operator identification, substrate and coating description, instrument and calibration status, environmental and location planning, individual readings, optional independent re-checks, statistical summary, tolerance and compliance evaluation, anomalies and corrective actions, supporting evidence, self-assessment, and reviewer sign-off. The form explicitly states that it is a general-purpose record rather than a substitute for any project-specific procedure, drawing note or specification, which is a helpful and honest framing for respondents.
The introductory paragraphs give clear guidance on consistency of units and on which fields are required, reducing ambiguity before data entry begins.
I confirm that the readings recorded here were taken by me (or under my direct supervision) and reflect what was actually measured on the workpiece. This attestation question establishes authorship of the data at the point of entry. Practically, it links each record to a responsible person and discourages transcription of readings taken by an unidentified third party.
Have you reviewed the written measurement procedure or work instruction that applies to this job? Asking this up front helps a reviewer understand whether the readings follow a defined method or an ad-hoc agreement. The yes follow-up captures a procedure reference, while the no follow-up asks how the method was determined, which is a sensible way to document judgement-based work without blocking completion.
Is this measurement being taken as part of a batch sample rather than on every item produced? This distinction matters when interpreting results, because a sampled measurement supports statements about a batch rather than every individual item. The follow-up prompts the respondent to state the sampling approach used.
Sample ID/Item identifier anchors the whole record to a specific item or panel and is the primary lookup key for later retrieval.
Job, order or work reference number and Item or component description provide useful operational context and make the record traceable to the work package it belongs to.
Number of items in the batch or lot gives scale to the measurement exercise and helps a reviewer judge how representative the sample might be.
Date of measurement and Time measurement started establish a timeline, which is particularly relevant when readings are compared across shifts, days or after a cure period.
Measured by (name), Department, team or laboratory and Contact email or phone for follow-up form a simple accountability and communication trail, so queries about a reading can be resolved without searching for the original operator.
Is this a re-measurement taken after an earlier set of readings? Capturing repeat measurement history in the record itself avoids the need to cross-reference multiple documents when assessing whether conditions have changed.
Stage at which the measurement is being taken offers a well-chosen list of production and inspection stages, with targeted follow-ups for service-exposure and failure-investigation scenarios. This single field materially changes how any thickness result should be read.
The section opens with an explanatory paragraph acknowledging that substrate type and surface condition influence which measurement principle is appropriate, which is helpful orientation for less experienced respondents.
Substrate material family provides a broad but practical material taxonomy, with sensible follow-ups for steel grade, aluminium alloy and uncertain cases.
Is the substrate magnetic (ferromagnetic)? is a useful screening question, since magnetic versus non-magnetic conductive substrates typically point to different instrument principles. The nested follow-up for non-magnetic conductive substrates adds informative context while deferring to the organisation’s own method statement.
Substrate thickness, if relevant to the method used is appropriately optional, since its relevance depends on the chosen principle.
Surface preparation or condition of the substrate before coating and Approximate surface roughness of the substrate together describe the interface that readings depend on. Surface texture in particular can influence the spread of values at a single location.
Geometry of the measurement area recognises that curvature, internal surfaces, edges and complex shapes can challenge probe seating. Targeted follow-ups capture curvature radius and tube or wire diameter where that matters.
Was the substrate verified as being the correct material before measurement began? promotes a documented material check, with a follow-up covering certificates, identification testing, simple field checks or visual knowledge.
Coating or treatment type being measured covers a wide practical range from liquid-applied paint through metallic, plated, anodised, thermal-spray, film and liner systems, with product, metal, film-grade and free-text follow-ups.
Number of coating layers or coats applied and Coating colour, finish or batch/lot code capture concise process and traceability detail that often explains localised thickness variation.
Application method used to apply the coating is relevant background when interpreting heavy build near edges or sag-prone areas.
Has the coating been fully cured, dried or aged before measurement? is a thoughtful inclusion, because readings taken before full cure can differ from those taken afterwards. Both branches ask for useful documentation: cure time and conditions, or the reason and precautions if measuring early.
Is the coating system multi-layer, with different materials in each layer? routes to a layered description, and the Coating Layer Schedule table provides a compact per-layer record with layer number, material, nominal thickness, colour or code and a flag for whether the layer was measured separately.
Any special features of the coating system worth noting gives space for characteristics that can affect readings, such as soft or easily deformed layers, without forcing respondents into predefined categories.
Instrument ID/asset number ties each dataset to a specific device on the equipment register, which is fundamental for later review or comparison.
Instrument make and model and Instrument resolution or least count (in the unit used) add the detail needed to understand what level of difference between readings is meaningful.
Measurement principle used lists commonly encountered principles and includes targeted follow-ups, for example whether a cross-section was metallographically prepared and at what magnification, or a description for alternative methods.
Date of last calibration or verification of the instrument and Next calibration or verification due date place the measurement within an instrument maintenance timeline.
Was the instrument checked against reference foils, standards or a certified sample immediately before the measurement? is one of the strongest design choices in the form. The yes branch leads to a Pre-measurement Verification Record table that includes certified reference value, indicated value, an automatically calculated difference (indicated minus reference) and an acceptable-check-limits flag. The no branch still allows the session to proceed while requiring an explanation.
Was the instrument zeroed or calibrated on an uncoated area of the same substrate before use? prompts documentation of the zero reference location, which supports reproducibility.
Was the probe or sensor cleaned or checked for damage before measurement? captures a simple pre-use condition check, with a free-text follow-up where a concern exists.
Operator experience with this instrument offers a four-level experience scale and a supervision question for first-time users, which is a pragmatic way to contextualise confidence in the data.
Ambient temperature during measurement (°C), Relative humidity during measurement (%) and Surface temperature of the part, if measured (°C) record the environment concisely and are useful when comparing results taken on different days.
Location of the measurement distinguishes workshop, field, production line and storage settings, with a site description follow-up for field work.
Surface condition at the time of measurement is a well-built multiple-choice item whose follow-ups handle dust (was the surface cleaned?), moisture (how was it managed?) and difficult access (were special safety arrangements in place, and what were they).
How measurement locations were selected covers grid patterns, marked drawings, nominated critical areas, random selection, edge comparisons and customer-agreed positions, with a drawing upload or description follow-up as appropriate.
Planned number of measurement locations on this part and Number of repeat readings taken at each location set expectations against which the readings table can be checked.
Were locations spaced far enough apart to avoid overlapping readings? is a subtle but useful quality question, since closely spaced readings can reflect overlapping sensing areas rather than true local variation.
Please upload a photo of the part or surface showing where measurements were taken (optional) adds visual context at low effort cost.
Unit used for all thickness values in this form appears immediately before the readings table, reinforcing the single-unit convention stated in the introduction.
The Measurement Location Readings and Calculated Values table is the operational core of the form. Each row captures a location ID and description alongside three repeat readings, then calculates location average (rounded to two decimal places), minimum, maximum, spread (maximum minus minimum) and deviation from nominal automatically. A nominal specified thickness column and a Within specified range? checkbox let the operator record a per-location judgement. The included example rows illustrate both compliant and non-compliant locations, which helps respondents understand the expected entry pattern.
Notes on individual readings gives room for explanations such as edge effects, probe slip or surface defects at specific locations.
Were any readings discarded or repeated during the session? encourages transparency about data exclusion, with a follow-up asking which readings were set aside and why.
Was an independent re-check of the readings carried out (second instrument, second operator or different method)? is a proportionate optional layer of assurance. The Independent Re-check Comparison table records the original average, the re-check value, an automatically calculated difference (re-check minus original), the re-check instrument or operator, and an acceptability flag. Where no re-check is recorded, the form still provides a neutral prompt noting that a re-check may be useful if results are later disputed.
Was the measurement repeated after adjusting probe pressure, couplant or technique? captures technique sensitivity, which can explain apparent variation between sessions.
The section asks respondents to state which convention they used before summarising, which avoids ambiguity when the figures are reviewed later.
Basis used for the summary statistics lets the user choose between all individual readings, location averages only, or final accepted readings only. This is a thoughtful inclusion because the chosen basis changes how the summary should be interpreted.
Total number of readings included in the summary, Overall average thickness, Minimum thickness recorded, Maximum thickness recorded, Range (maximum minus minimum) and Standard deviation of the readings (if calculated) form a compact descriptive statistics set.
The displayed formulas for Mean (average) thickness and Sample standard deviation make the calculation basis explicit for anyone reading the record.
Is the variation across the surface considered uniform for this application? invites an interpretive judgement, with follow-ups either documenting the basis for a uniform finding or describing the observed pattern of variation.
Source of the specified thickness requirement distinguishes drawings, customer documents, internal guides, product data sheets, verbal agreements and cases where no formal specification exists. Reference follow-ups for each source type strengthen traceability.
Specified minimum thickness (lower limit) and Specified maximum thickness (upper limit) define the acceptance band, while Nominal or target thickness, if stated supports the deviation calculation used in the readings table.
Unit used for the specified range prevents unit-mismatch errors when the range is entered separately from the readings.
Are all measured values within the specified range? drives a rich conditional branch. The no side asks which condition best describes the out-of-range result, with follow-ups for thin locations, heavy locations, excessive variation and readings too close to a limit to judge confidently. This is a well-designed diagnostic structure.
Overall compliance result provides five clear outcomes including compliant, compliant with comment, non-compliant, cannot be determined and not assessed, each with an appropriate explanatory follow-up.
Disposition of the measured item closes the loop operationally with accept, accept with deviation, rework, reject, hold or not-applicable outcomes, including follow-ups on authorised deviations, re-measurement after rework and pending reviews.
Did you observe any of the following during the measurement? is a well-chosen defect checklist covering blistering, cracking, pinholes, runs, colour variation, contamination and probe damage, with location and size follow-ups and a probe-marking question.
Likely contributing factor, in your view is framed as opinion rather than diagnosis, which is appropriate for an inspection record.
Please describe any action taken or recommended, Person or team responsible for the action and Target completion date for the action create a lightweight but complete action-tracking thread.
Does this result need to be shared with anyone else (for example production, engineering or the requester)? routes the record to the right audience with a distribution follow-up.
The evidence section offers targeted upload slots: Instrument printout, screenshot or data export showing the readings, Photo of the measurement surface close-up, Photo of the instrument display at a measurement location, Reference drawing, sketch or specification extract used for the specified range and Calibration certificate or verification record for the instrument used. Each corresponds to a natural review question.
Are there any further attachments to follow later? acknowledges real-world reporting timelines where certificates arrive after the field record is filed.
The matrix rating item asks the operator to score six statements covering procedure clarity, instrument setup, representativeness of locations, suitability of conditions, data completeness and support for the compliance judgement. This produces a concise confidence profile that reviewers can scan quickly.
Overall, how confident are you in these results? provides a single numeric score on a five-point scale.
Anything that would make these results more reliable next time turns each measurement session into a small, practical improvement opportunity.
Reviewed by (name and role) and Date of review establish a second-party review point.
Outcome of the review offers four realistic outcomes with follow-ups for corrections, additional measurement and escalation.
The checkbox confirming consistency between readings, summary values and compliance result is a simple internal consistency check at sign-off.
Signature of the person who carried out the measurement and Signature of the reviewer or approver complete the accountability chain, while Date the record was completed and Record or report reference assigned to this measurement support filing and retrieval.
The form’s greatest strength is its disciplined progression from context to evidence to judgement. It captures enough surrounding information to explain why a reading might vary, including substrate type, surface texture, geometry, cure state, environment, instrument condition and operator experience, while delegating arithmetic to built-in formulas for averages, minima, maxima, spread, deviation and check differences. The conditional logic is purposeful rather than decorative: most follow-ups appear only where the answer creates a genuine documentation need. The inclusion of an attestation, a per-location readings table with repeat readings, an optional independent re-check and a formal disposition step gives the record a practical, audit-friendly shape without overwhelming the respondent. Privacy-wise, the form collects a name and contact details alongside technical data, so organisations may wish to align retention and access arrangements with their own internal handling practices.
Areas worth considering include the overall length of the form, which is substantial and may benefit from being completed in more than one sitting for complex jobs; the separation of the readings unit from the specified range unit, which is sensible but relies on the respondent to keep them consistent; and the statistical summary fields, which are entered manually even though several underlying values are calculated in the readings table. A lighter-weight variant for routine, repeat jobs with unchanged substrate, coating and instrument could reduce effort for high-frequency use while retaining the core readings and compliance sections. Finally, because the form is explicitly a general-purpose template, users should verify that any field names, tolerance bands or acceptance criteria align with the documents that apply to their own work before relying on the record for decisions.
Mandatory Question Analysis for Coating Thickness Measurement Form – Readings, Averages & Compliance Record
Important Note:
This section explains why certain fields in this form are marked as required and provides general guidance on how these requirements may support the collection of complete, accurate and relevant information.
Required fields and information-collection obligations may vary depending on your industry, jurisdiction, business operations and intended use of the form. A field marked as required in this template does not necessarily mean that collecting the information is legally mandatory.
Please review each required field to determine whether it is necessary, appropriate and lawful for your particular purpose. Consider applicable privacy, data protection, consent and industry-specific requirements, and consult an appropriately qualified legal, privacy or compliance professional where necessary.
Please delete this section before publishing your form. See our Terms of Service for further information.
I confirm that the readings recorded here were taken by me (or under my direct supervision) and reflect what was actually measured on the workpiece.
Recommendation: Requiring this attestation ties each record to a named individual at the moment of submission and discourages the entry of readings whose origin is unclear. It supports straightforward record-keeping when results are queried later. Its necessity depends on how the form creator intends to use the record; where measurements are routinely logged on behalf of a team, consider adjusting the wording to reflect the accepted working practice.
Have you reviewed the written measurement procedure or work instruction that applies to this job?
Recommendation: Requiring this response means every record begins with a clear statement of whether a defined method was followed or an ad-hoc approach was agreed. This aids consistency when datasets from different operators are compared. Keep the follow-up fields optional so respondents can proceed even when no written procedure exists for the job in question.
Sample ID/Item identifier
Recommendation: Requiring an item identifier ensures each measurement record can be retrieved and associated with a specific piece of work. Without it, results become difficult to match to production or inspection records. Confirm whether your organisation uses a fixed coding convention so that respondents enter identifiers in a consistent format.
Number of items in the batch or lot
Recommendation: Requiring the batch or lot size gives scale to the measurement exercise and helps a reviewer judge how representative the sampled readings may be. If the form is also used for one-off panels or test coupons, consider allowing a simple value such as 1 and stating that convention in the instructions.
Date of measurement
Recommendation: Requiring the measurement date anchors the record in time and allows results to be correlated with production shifts, cure periods or environmental conditions. It is a basic record-keeping anchor for almost any measurement log.
Measured by (name)
Recommendation: Requiring the operator name creates an accountability link for the data and provides a clear point of contact if a reading needs clarification. Depending on your internal data handling practices, consider explaining briefly how operator names will be stored and who may access them.
Substrate material family
Recommendation: Requiring the substrate family supports interpretation of thickness readings, since the substrate strongly influences which measurement principle is suitable and how values are understood. Where the material is unknown at the time of measurement, the provided option keeps the respondent moving while recording that uncertainty accurately.
Is the substrate magnetic (ferromagnetic)?
Recommendation: Requiring this binary response provides a quick screening indicator of the likely instrument principle and helps reviewers judge whether the recorded method is plausible for the part. It is a low-effort field that meaningfully improves the readability of the rest of the record.
Coating or treatment type being measured
Recommendation: Requiring the coating type provides the essential context for every subsequent thickness value and aligns the record with product or process documentation. The broad option list reduces the chance of free-text ambiguity; confirm whether any additional local coating categories should be added to the list.
Instrument ID/asset number
Recommendation: Requiring the instrument identifier links the dataset to a specific device and its maintenance history, which is central to reviewing measurement reliability later. Ask operators to use the identifier exactly as shown on the equipment register to keep records searchable.
Measurement principle used
Recommendation: Requiring the measurement principle allows a reviewer to assess whether the method suits the substrate and coating combination described in the record. It also makes repeat measurements more reproducible, since the technique is stated rather than inferred.
Date of last calibration or verification of the instrument
Recommendation: Requiring this date places the measurement within the instrument’s maintenance timeline and makes it straightforward to confirm that equipment was within its usual check interval at the time of use. The adjacent optional field for the next due date adds useful forward-looking context.
Was the instrument checked against reference foils, standards or a certified sample immediately before the measurement?
Recommendation: Requiring this question ensures every record states whether a pre-use check was performed, with the verification table capturing reference values and indicated values when it was. The negative branch still permits submission with an explanation, which keeps the record usable for situations where a check was not practical.
How measurement locations were selected
Recommendation: Requiring the location selection approach helps reviewers judge how representative the readings are of the whole surface and supports consistent sampling between shifts or batches. The drawing upload or description follow-up provides evidence for grid or marked-drawing approaches.
Planned number of measurement locations on this part
Recommendation: Requiring the planned number of locations sets an expectation that can be checked against the readings table and makes any shortfall visible at review. It also encourages the operator to plan the exercise before taking readings.
Unit used for all thickness values in this form
Recommendation: Requiring the unit statement reduces the risk of ambiguous values in the readings table and supports consistency across the record. Placing it immediately before the table is good positioning; consider also referencing this unit in any summary or report produced from the data.
Basis used for the summary statistics
Recommendation: Requiring this choice ensures the summary figures can be interpreted correctly, since statistics calculated from all individual readings, from location averages only, or from accepted readings only can differ. It is a small field that prevents significant misreading of the data set.
Source of the specified thickness requirement
Recommendation: Requiring the specification source documents where the acceptance expectation came from and supports traceability when results are reviewed or compared. The option to record that no formal specification was supplied prevents invented targets and keeps the record honest.
Specified minimum thickness (lower limit)
Recommendation: Requiring the lower limit provides one half of the acceptance band used for the compliance judgement and links back to the documented source. Where no formal range applies, the surrounding form guidance already prompts the user to record that clearly rather than estimating.
Specified maximum thickness (upper limit)
Recommendation: Requiring the upper limit completes the acceptance band and enables a consistent comparison with the measured values. Together with the lower limit, it forms the reference point for both the per-location flags in the readings table and the overall result.
Unit used for the specified range
Recommendation: Requiring the unit for the tolerance range guards against mismatches when the limits are entered separately from the measurements. Confirming the unit at the point of entry is a simple control that avoids a common source of data error.
Are all measured values within the specified range?
Recommendation: Requiring this question produces a clear per-session compliance statement and drives the diagnostic follow-ups that record the nature of any out-of-range result. It gives the record a definite conclusion rather than leaving the judgement to the reader.
Overall compliance result
Recommendation: Requiring the overall result ensures that every completed record ends with an explicit outcome, including cases where the result cannot be determined or no specification applied. This supports downstream processing and reporting without requiring anyone to re-derive the conclusion.
Disposition of the measured item
Recommendation: Requiring a disposition ensures the measurement leads to a clear operational next step for the item, whether release, deviation, rework, rejection or hold. It also prompts follow-up details such as who authorised a deviation or when a re-measurement is planned.
Signature of the person who carried out the measurement
Recommendation: Requiring the measurement signature formalises the attestation captured earlier in the form and provides a clear sign-off point for the dataset. It is consistent with common internal record-keeping practice for inspection data, although the exact sign-off expectation should reflect the form creator’s own procedures.
Date the record was completed
Recommendation: Requiring the completion date distinguishes when measurements were taken from when the record was finalised, which matters when readings and supporting evidence are gathered over more than one session. It also supports orderly filing and chronological retrieval.
The form uses a relatively large set of required fields, spread across identification, substrate, coating, instrument, location planning, readings, specification and sign-off. This reflects the record’s role as a traceable measurement document, where a missing element can make a dataset hard to interpret. Even so, a few proportionate adjustments can help balance data depth against completion effort.
Overall, the required set is well aligned with the form’s purpose of producing a complete, reviewable thickness measurement record. The main opportunity is to make the requirement level slightly more responsive to job complexity, so that straightforward measurements can be recorded quickly while detailed investigations still receive the full level of documentation.