Battery Pack Reclamation Log — Record Every Step of Experimental & End-of-Life Pack Decommissioning

1. Section 1 — Facility & Battery Serial Identification

Use this section to establish traceability for the batch. Record where the packs were held, how they are identified, and which documentation accompanies them. Accurate identification at this stage supports material reconciliation and later audits of the reclamation chain.

 

Facility or plant name

Internal site or plant code

Assembly line, cell, or storage area where packs were removed

Reclamation log reference number

Date this log was opened

Date and time pack removal from service began

Total number of packs in this batch

Primary reason the packs are being decommissioned

 

Please describe the experimental programme and why it is being wound down:

 

Please summarise the quality issue or hold reference:

 

Please describe the damage or incident and any prior investigation:

 

Please describe the reason for decommissioning:

Battery pack serial or part number (first pack in batch)

Module serial range covered by this log

Pack form factor

Are all serial identifiers and labels legible?

 

Please list the affected units and describe the labelling issue (for example, heat damage, adhesive failure, over-stamping):

Pack identification inventory

Pack serial number

Model or variant

Modules per pack

Nominal voltage (V)

Rated capacity (Ah)

Pack build date

Gross mass (kg)

A
B
C
D
E
F
G
1
BP-48V-2027-000184
EX-7 Pilot
12
48.60
210.00
11/4/2027
186.50
2
BP-48V-2027-000185
EX-7 Pilot
12
48.40
210.00
11/4/2027
187.10
3
 
 
 
 
 
 
 
4
 
 
 
 
 
 
 
5
 
 
 
 
 
 
 
6
 
 
 
 
 
 
 
7
 
 
 
 
 
 
 
8
 
 
 
 
 
 
 
9
 
 
 
 
 
 
 
10
 
 
 
 
 
 
 

Which supporting documents accompany this batch?

Photograph of the pack identification label

Choose a file or drop it here

Upload the build record or batch documentation

Choose a file or drop it here
 

Person completing this identification section

2. Section 2 — State of Health & Chemical Composition Profile

Describe the electrical condition and the material makeup of the packs before any disassembly begins. A clear state-of-health picture helps determine handling precautions, whether cells can be reused or must be treated as scrap, and how the material streams should be allocated later.

 

Reference calculation for state of health

SOH(%)=CmeasuredCrated×100\mathrm{SOH}(\%) = \frac{C_{\text{measured}}}{C_{\text{rated}}} \times 100

 

Rated pack capacity (Ah)

Measured pack capacity at last diagnostic (Ah)

Calculated state of health (%)

State-of-health band assigned to this batch

 

Please explain why a measurement could not be obtained (for example, open circuit, damaged busbar, missing instrumentation):

Pack open-circuit voltage at rest (V)

Measured internal resistance (mOhm)

Estimated residual energy remaining in pack (kWh)

Residual charge condition at time of logging

 

Approximate remaining state of charge (%):

 

Please explain why the pack was not discharged and what interim controls are in place:

Dominant cell chemistry

 

Please describe the next-generation chemistry and any handling guidance supplied by the cell vendor:

 

Please list the chemistries present and how they are arranged within the pack:

 

Please describe how the chemistry will be confirmed before processing:

Which hazardous or regulated constituents are expected to be present?

Are any cells visibly swollen, leaking, vented, or discoloured?

 

Please describe the affected units, the observed condition, and any odour or residue noted:

Has this batch experienced any thermal event, smoke, or off-gassing during its service life?

 

Please summarise the event, when it occurred, and the outcome of any investigation:

Condition assessment of pack sub-systems

Poor

Below expectation

Acceptable

Good

Excellent

Cell blocks and module frames are intact

Cell tabs and busbars show no corrosion or arcing marks

Battery management electronics are undamaged

Harnesses and connectors are intact and identifiable

Cooling plates, hoses, and fittings show no leaks

Enclosure, seals, and mounting hardware are serviceable

Measured self-discharge since last test (% per month)

Date of the most recent diagnostic or capacity test

Upload the diagnostic or capacity test report

Choose a file or drop it here
 

Photograph of any visible cell damage, swelling, or residue

Choose a file or drop it here

Additional notes on state of health, anomalies, or measurement limitations

3. Section 3 — Disassembly & Hazardous Material Handling Steps

Document the sequence actually followed on the floor, the controls applied, and any hazardous materials released or recovered. Where a step could not be completed as planned, record the deviation and the alternative control used rather than leaving the entry blank.

 

Which isolation and preparation steps were completed before opening the pack?

Primary method used to bring the pack to a safe energy state

 

Equipment identifier or asset number used:

 

Please describe the alternative controls used in place of discharge:

Disassembly step log

Step no.

Task performed

Tooling or equipment used

Duration (min)

PPE level applied

Completed

Deviation or observation

A
B
C
D
E
F
G
1
1
Outer enclosure removal
Torque driver, lifting frame
25
Standard plus face shield
None
2
2
Busbar and harness disconnection
Insulated hand tools
35
Class 0 gloves plus apron
One corroded stud required manual release
3
3
Module extraction and segregation
Module trolley
45
Standard plus face shield
Two modules retained pending further inspection
4
 
 
 
 
 
 
5
 
 
 
 
 
 
6
 
 
 
 
 
 
7
 
 
 
 
 
 
8
 
 
 
 
 
 
9
 
 
 
 
 
 
10
 
 
 
 
 
 

How was any liquid electrolyte handled?

 

Extraction equipment or capture method used:

 

Please describe the release, the containment action, and the area affected:

Estimated volume of electrolyte recovered (L)

Did any spill, leak, or uncontrolled release occur during disassembly?

 

Please describe what was released, the approximate quantity, the containment method, and the clean-up outcome:

Which personal protective equipment was issued to the team?

Ventilation approach used in the disassembly area

Was a fire watch or standby team maintained throughout the operation?

 

Name or team designation of the fire watch and the shift covered:

 

Please explain why a fire watch was not maintained and what alternative monitoring was used:

Number of personnel involved in the disassembly

Shift start time

Shift end time

How were separated cell blocks staged after removal?

Photograph of the disassembly workstation and containment setup

Choose a file or drop it here

Upload the waste tracking or consignment documentation generated during this step

Choose a file or drop it here
 

I confirm that the steps recorded above reflect the work as actually performed, including any deviations.

4. Section 4 — Downstream Recycling Partner Allocation

Allocate each recovered material stream to a downstream partner and record what left the site. The table below calculates estimated recovered output from the mass and recovery rate you enter, giving a simple material balance for reconciliation.

 

Primary downstream partner or processor name

Type of downstream partner

 

Please describe the intended second-life application and the screening the partner will perform first:

 

Please describe the partner's role in the chain:

Which material streams were allocated for downstream processing?

Material allocation and recovery balance

Material stream

Mass sent (kg)

Expected recovery rate (%)

Estimated recovered output (kg)

Credit or charge per batch

Destination or facility reference

A
B
C
D
E
F
1
Aluminium housings
420.50
92.0
386.86
$310.00
REF-AL-221
2
Copper busbars and cabling
96.20
88.0
84.66
$540.00
REF-CU-078
3
Cell and module fractions
1280.00
71.0
908.80
$125.00
REF-CELL-014
4
 
 
 
 
 
 
5
 
 
 
 
 
 
6
 
 
 
 
 
 
7
 
 
 
 
 
 
8
 
 
 
 
 
 
9
 
 
 
 
 
 
10
 
 
 
 
 
 

Total value credited or charged for this batch

Consignment, manifest, or tracking number

Dispatch date from the plant

Transport mode used to move the material

Which handling credentials does the partner state that they hold?

Did the partner provide written acceptance and processing documentation?

 

Upload the partner acceptance or processing documentation

Choose a file or drop it here
 
 

Please explain why documentation was not provided and when it is expected:

Please rank the criteria that mattered most when selecting this partner (most important first)

Material recovery performance

Proximity to the plant

Cost or credit terms

Turnaround time

Documented process transparency

Capacity to handle damaged or hazardous units

Overall performance rating for this partner on this batch

Comments on partner performance, delays, rejected loads, or follow-up actions

I confirm that the quantities recorded here match the dispatch documentation held on site.

5. Section 5 — Environmental Health & Safety (EHS) Clearance Sign-Off

This closing section records the internal review of the work area, the residual hazards, and the decision to release the site and the remaining materials. Complete it after disassembly and dispatch are finished so that any open items are captured before the log is closed.

 

Please rate the following review points for this decommissioning activity

Strongly disagree

Disagree

Neutral

Agree

Strongly agree

Work area was left clean and free of residues

Hazardous materials were segregated and labelled correctly

Emergency equipment remained accessible throughout

Ventilation and monitoring performed as expected

Waste streams were recorded completely and accurately

Team members understood the task-specific precautions

Do any residual hazards remain in the work area or in stored material?

 

Please describe each residual hazard, its location, and the control or isolation currently applied:

Were any of the following observed during the operation?

 

Please describe the injury or near miss and the immediate response:

 

Please describe the exposure, the route, and any first aid or medical response:

 

Please describe what happened and how the circuit was made safe:

 

Please describe the thermal event and the response taken:

 

Please describe the spill, the volume estimate, and the clean-up method:

 

Please describe the equipment failure and any repair or quarantine action:

Overall residual risk rating for the remaining activity on site

Corrective actions, open items, or conditions attached to this clearance

Is a follow-up review required before the log can be closed?

 

Target date for the follow-up review:

How confident are you that the remaining material can be handled safely by the next team?

EHS reviewer name

Role or title of the reviewer

Plant manager or accountable supervisor name

Reviewer signature

Date of sign-off

I confirm that this log is a complete and accurate record of the reclamation activity described, to the best of my knowledge.

Upload any supporting inspection photographs, monitoring readings, or clearance notes

Choose a file or drop it here
 

Final remarks for the record

Analysis for Battery Pack Reclamation & Decommissioning Log Template

Important Note:

This analysis provides strategic insights to help you get the most from your form's submission data for powerful follow-up actions and better outcomes.

AI-Generated Content: This template and its accompanying guidance are AI-generated to provide a practical starting point for your form-building needs. Please review and customise the content to ensure it is accurate, appropriate and suitable for your intended use.

This guide is provided for general informational and planning purposes only. It does not constitute professional, legal, financial, medical, employment, privacy, regulatory, or advice of any other kind, nor does it certify that this template is suitable or compliant for any particular jurisdiction or purpose.

Laws, regulations, industry practices and business requirements vary. You are responsible for reviewing and customising the template to suit your intended use and obtaining advice from appropriately qualified professionals where necessary.

Please delete this section before publishing your form. See our Terms of Service for further information.


 

Overall Form Analysis

The Battery Pack Reclamation & Decommissioning Log Template is a well-structured, five-section operational record designed for assembly plant managers who are decommissioning experimental or end-of-life battery packs. The form systematically captures the full reclamation chain—from initial facility and serial identification through state-of-health assessment, disassembly and hazardous material handling, downstream recycling partner allocation, and final EHS clearance sign-off. Its layered structure mirrors the real-world sequence of a decommissioning workflow, which supports logical data entry and reduces the likelihood of skipped or misplaced information. The inclusion of conditional follow-up questions, pre-populated table examples, a state-of-health reference formula, and a calculated recovery balance column in the material allocation table demonstrates thoughtful design aimed at both accuracy and practical usability on the plant floor.

 

Section 1 — Facility & Battery Serial Identification

Facility or plant name — This field establishes the originating site for the reclamation batch, which is foundational for traceability and multi-site reconciliation. This is essential for cross-referencing the record with other documentation systems, audit trails, and dispatch manifests.

 

Internal site or plant code — An optional field that complements the plant name with a structured code, supporting automated sorting or database lookups. Keeping it optional is reasonable since not all organizations use coded identifiers.

 

Facility location reference — The map element provides a geographic anchor for the batch. This can be useful for logistics planning and for verifying that the correct site is recorded, particularly in organizations with multiple facilities.

 

Assembly line, cell, or storage area where packs were removed — Capturing the specific work area within the plant narrows down the origin of the packs and can support root-cause analysis if quality or safety issues arise later.

 

Reclamation log reference number — A unique identifier for the log itself. This is essential for cross-referencing the record with other documentation systems, audit trails, and dispatch manifests.

 

Date this log was opened — Establishes the chronological start of the reclamation activity and anchors all subsequent timestamps within the record.

 

Date and time pack removal from service began — Captures the precise operational start time, which can be relevant for shift planning, incident timelines, and energy-state management.

 

Total number of packs in this batch — Defines the scope of the batch and provides a quantity check against the detailed inventory table and downstream dispatch records.

 

Primary reason the packs are being decommissioned — This single-choice field with conditional follow-ups is an effective design choice. It categorises the decommissioning trigger while allowing respondents to elaborate only when the selected reason warrants additional context (e.g., experimental programme details, quality hold references, or incident descriptions). This keeps the form concise for routine cases while capturing depth where needed.

 

Battery pack serial or part number (first pack in batch) — Records the lead serial number for the batch. Combined with the module serial range field and the pack identification inventory table, it supports precise unit-level tracking.

 

Module serial range covered by this log — Optional but valuable for batches where module-level traceability is needed, such as when modules may be redistributed or tested individually.

 

Pack form factor — Categorising the physical cell format (prismatic, pouch, cylindrical, mixed, or unknown) informs downstream handling and recycling decisions, as different form factors may require different disassembly approaches.

 

Are all serial identifiers and labels legible? — A yes/no gate with a conditional follow-up for illegible labels. This is a practical check that surfaces traceability gaps early, before disassembly proceeds and labels may be further damaged.

 

Pack identification inventory — The table with example rows provides a structured, per-pack record including serial number, model, module count, voltage, capacity, build date, and gross mass. Pre-populated examples guide respondents on the expected data format and precision. This table is central to material reconciliation and mass-balance calculations later in the process.

 

Which supporting documents accompany this batch? — A multiple-choice checklist that inventories available documentation. This is useful for audit readiness and for identifying documentation gaps before the batch leaves the site.

 

Photograph of the pack identification label — An image upload that provides visual evidence of the label state at the time of logging, supporting later verification if serial numbers are disputed.

 

Upload the build record or batch documentation — A file upload for attaching the primary build or traveller record, consolidating key documentation within the log.

 

Person completing this identification section — Captures accountability for the identification data. This supports quality assurance and provides a point of contact for any follow-up queries.

 

Section 2 — State of Health & Chemical Composition Profile

Reference calculation for state of health — The inclusion of an explicit formula (SOH = measured capacity/rated capacity × 100) is a strong design choice. It standardises the calculation approach and reduces variability in how respondents derive the SOH percentage.

 

Rated pack capacity (Ah) — The baseline reference value for SOH calculation. Collecting this value allows respondents to calculate state of health using the reference formula when reliable capacity information is available.

 

Measured pack capacity at last diagnostic (Ah) — The numerator in the SOH formula. Together with the rated capacity, it enables the calculated SOH to be verified.

 

Calculated state of health (%) — The derived SOH value. Although not explicitly calculated by the form, the presence of the formula and the two input fields guides respondents to compute it consistently.

 

State-of-health band assigned to this batch — A banded classification with a conditional follow-up for unmeasurable cases. This simplifies downstream decision-making by grouping packs into actionable categories (e.g., near new, moderate fade, significant fade, heavily degraded) while capturing the reason when measurement is not possible.

 

Pack open-circuit voltage at rest (V) — A basic electrical characteristic that supports safety assessment and handling decisions.

 

Measured internal resistance (mOhm) — Internal resistance is an indicator of cell degradation and can help differentiate between healthy and degraded packs, informing whether cells are candidates for reuse or must be treated as scrap.

 

Estimated residual energy remaining in pack (kWh) — Quantifies the stored energy that must be safely managed during disassembly. This is a practical safety-relevant data point.

 

Residual charge condition at time of logging — With conditional follow-ups for partially discharged and not-discharged states, this field captures the energy state at intake and prompts the respondent to record interim controls when the pack is not at a safe handling level.

 

Dominant cell chemistry — A mandatory field with follow-ups for next-generation, mixed, and unknown chemistries. Chemistry classification is operationally important because it influences handling precautions, recycling stream allocation, and material recovery expectations. The conditional follow-ups for edge cases are well-designed.

 

Which hazardous or regulated constituents are expected to be present? — A multiple-choice checklist that inventories expected hazardous materials. This supports downstream waste classification and helps ensure that appropriate handling and disposal pathways are identified.

 

Are any cells visibly swollen, leaking, vented, or discoloured? — A mandatory visual condition check with a detailed follow-up for affected units. This surfaces physical defects that may indicate thermal or chemical hazards before disassembly begins.

 

Has this batch experienced any thermal event, smoke, or off-gassing during its service life? — A historical safety check with a follow-up for positive responses. Understanding prior thermal events helps inform handling precautions and may indicate elevated risk during disassembly.

 

Condition assessment of pack sub-systems — A matrix rating across six sub-systems (cell blocks, tabs and busbars, BMS electronics, harnesses, cooling system, enclosure) using a five-point scale. This provides a structured, comparable condition snapshot that can inform disassembly planning and downstream routing decisions.

 

Measured self-discharge since last test (% per month) — An optional metric that can indicate internal cell degradation or parasitic drain, useful for technical assessment.

 

Date of the most recent diagnostic or capacity test — Provides temporal context for the SOH and electrical measurements, helping assess data freshness.

 

Upload the diagnostic or capacity test report — Consolidates the underlying test data within the log for reference and audit purposes.

 

Photograph of any visible cell damage, swelling, or residue

 

Additional notes on state of health, anomalies, or measurement limitations — An open-ended field that captures nuances not covered by the structured fields, such as outlier modules or environmental conditions during testing.

 

Section 3 — Disassembly & Hazardous Material Handling Steps

Which isolation and preparation steps were completed before opening the pack? — Structured checklist covering relevant pre-disassembly preparation and safety controls. The applicable steps depend on the battery configuration, task risk assessment, and established site procedures.

 

Primary method used to bring the pack to a safe energy state — With conditional follow-ups for vendor equipment identification and alternative controls when no discharge was performed, this field documents the energy management approach and prompts justification for deviations.

 

Disassembly step log — A detailed table capturing each step (task, tooling, duration, PPE level, completion status, and deviations). Pre-populated example rows demonstrate the expected granularity. This is the operational heart of the form, providing a step-by-step audit trail of the physical work performed.

 

How was any liquid electrolyte handled? — A single-choice field with follow-ups for extraction method and unintentional releases. Electrolyte handling is a critical safety and environmental concern. This field helps document the electrolyte handling approach and supports subsequent review.

 

Estimated volume of electrolyte recovered (L) — Quantifies recovered electrolyte for material balance and waste tracking purposes.

 

Did any spill, leak, or uncontrolled release occur during disassembly? — A mandatory incident check with a detailed follow-up for positive responses. This mandatory check helps capture reported environmental and safety incidents and prompts additional documentation when a release occurs.

 

Which personal protective equipment was issued to the team? — Documents the PPE provision for the operation, supporting safety record-keeping and enabling review of whether appropriate protection was matched to the tasks performed.

 

Ventilation approach used in the disassembly area — Records the engineering controls applied to manage airborne hazards, which is relevant for both worker safety and environmental compliance documentation.

 

Was a fire watch or standby team maintained throughout the operation? — With follow-ups for both yes and no responses, this field documents fire safety provisions and prompts justification when no fire watch was arranged.

 

Number of personnel involved in the disassembly — Supports workforce tracking and can inform exposure assessments or shift planning analysis.

 

Shift start time and Shift end time — Capture the working window for the operation, useful for timeline reconstruction and labour tracking.

 

How were separated cell blocks staged after removal? — Documents the interim storage method for removed cell blocks, which is relevant for fire safety and material segregation.

 

Photograph of the disassembly workstation and containment setup — Provides visual evidence of the working conditions and containment measures in place.

 

Upload the waste tracking or consignment documentation generated during this step — Consolidates waste documentation within the log, supporting the downstream material allocation section.

 

I confirm that the steps recorded above reflect the work as actually performed, including any deviations. — A mandatory attestation checkbox that reinforces the accuracy of the step log and discourages incomplete or idealised entries.

 

Section 4 — Downstream Recycling Partner Allocation

Primary downstream partner or processor name — Identifies the receiving organisation for the recovered materials. This is a core traceability field for the reclamation chain.

 

Type of downstream partner — Categorises the partner (recycler, refiner, second-life integrator, etc.) with conditional follow-ups for second-life and other categories. This classification supports routing decisions and material balance analysis.

 

Which material streams were allocated for downstream processing? — A multiple-choice checklist that inventories the material categories released from the site, supporting waste stream accounting.

 

Material allocation and recovery balance — A well-designed table with a built-in formula (estimated recovered output = mass sent × recovery rate / 100) that automatically calculates expected recovery. Pre-populated example rows demonstrate the expected format. This table provides a simple but effective material balance for reconciliation and financial tracking.

 

Total value credited or charged for this batch — Captures the financial outcome of the batch, supporting cost tracking and partner performance evaluation.

 

Consignment, manifest, or tracking number — Links the log to external dispatch documentation for chain-of-custody purposes.

 

Dispatch date from the plant — Records when the material left the site, anchoring the logistics timeline.

 

Transport mode used to move the material — Documents the logistics method, which can be relevant for packaging and handling requirements.

 

Which handling credentials does the partner state that they hold? — A multiple-choice checklist of partner certifications and practices. This is self-declared information and serves as a reference point rather than verified credentialing.

 

Did the partner provide written acceptance and processing documentation? — A mandatory yes/no gate with conditional follow-ups. This reinforces data accuracy

 

Please rank the criteria that mattered most when selecting this partner — A ranking exercise that captures the decision-making priorities behind partner selection, useful for procurement review and future partner evaluation.

 

Overall performance rating for this partner on this batch — A star rating that provides a quick quantitative assessment of partner performance.

 

Comments on partner performance, delays, rejected loads, or follow-up actions — An open-ended field for qualitative feedback that may not be captured by the structured fields.

 

I confirm that the quantities recorded here match the dispatch documentation held on site. — An attestation checkbox that reinforces data accuracy for the material allocation table.

 

Section 5 — Environmental Health & Safety (EHS) Clearance Sign-Off

Please rate the following review points for this decommissioning activity — A matrix rating across six EHS review criteria using a five-point agreement scale. This provides a structured summary of the safety and environmental performance of the operation.

 

Do any residual hazards remain in the work area or in stored material? — A mandatory yes/no check with a detailed follow-up for positive responses. This ensures that open hazards are documented before the site is released.

 

Were any of the following observed during the operation? — A multiple-choice incident checklist with detailed conditional follow-ups for each event type (injury, exposure, electrical incident, thermal event, spill, equipment failure). This comprehensive capture mechanism ensures that all notable events are described in context.

 

Overall residual risk rating for the remaining activity on site — A digit rating that provides a quick quantitative risk assessment for handover purposes.

 

Corrective actions, open items, or conditions attached to this clearance — Captures outstanding items that must be addressed, supporting continuity of safety management.

 

Is a follow-up review required before the log can be closed? — With a conditional date field for follow-up scheduling, this ensures that unresolved items are tracked to completion.

 

How confident are you that the remaining material can be handled safely by the next team? — An emotion rating that captures the reviewer's subjective confidence level, which can complement the structured risk rating.

 

EHS reviewer name, Role or title of the reviewer, and Plant manager or accountable supervisor name — These identity fields establish clear accountability for the clearance decision at both the reviewer and supervisory levels.

 

Reviewer signature and Date of sign-off — Formalise the clearance with a signature and timestamp, completing the accountability chain.

 

I confirm that this log is a complete and accurate record of the reclamation activity described, to the best of my knowledge. — A mandatory attestation checkbox that reinforces the overall integrity of the log.

 

Upload any supporting inspection photographs, monitoring readings, or clearance notes — Provides a mechanism for attaching supplementary evidence to the clearance record.

 

Final remarks for the record — An open-ended closing field for any summary observations not captured elsewhere.

 

Overall Summary

This form demonstrates strong design principles for an industrial reclamation log. Its five-section structure closely mirrors the physical workflow, making it intuitive for plant-floor users. The use of conditional follow-up questions throughout is particularly effective—respondents are prompted for additional detail only when their answers warrant it, keeping the form efficient for routine cases while capturing depth for exceptions. Pre-populated table examples reduce ambiguity about expected data formats, and the inclusion of a state-of-health formula and a calculated recovery balance column adds practical value beyond simple data capture. The mandatory field selection is proportionate, focusing on traceability anchors (facility, serial numbers, log reference), safety-critical checks (cell condition, spill incidents, residual hazards), and accountability sign-offs. Areas for potential refinement include considering whether some optional fields (such as module serial range or internal site code) could benefit from conditional logic tied to batch size or site configuration, and whether the form could benefit from a brief progress indicator given its substantial length across five sections. Overall, the form is well-suited to its stated purpose of documenting the end-to-end decommissioning and reclamation of battery packs in a structured, auditable manner.

 

Mandatory Question Analysis for Battery Pack Reclamation & Decommissioning Log Template

Important Note:

This section explains why certain fields in this form are marked as required and provides general guidance on how these requirements may support the collection of complete, accurate and relevant information.

Required fields and information-collection obligations may vary depending on your industry, jurisdiction, business operations and intended use of the form. A field marked as required in this template does not necessarily mean that collecting the information is legally mandatory.

Please review each required field to determine whether it is necessary, appropriate and lawful for your particular purpose. Consider applicable privacy, data protection, consent and industry-specific requirements, and consult an appropriately qualified legal, privacy or compliance professional where necessary.

Please delete this section before publishing your form. See our Terms of Service for further information.

 

Mandatory Question Analysis

Facility or plant name
Recommendation: Requiring the facility name ensures that every reclamation log can be attributed to a specific originating site. In multi-plant operations, this field is a primary key for sorting, filtering, and cross-referencing records. Requiring it supports data completeness at the point of entry and reduces administrative effort during later reconciliation or audit activities. The necessity of this field depends on whether the organization operates across multiple locations; single-site operators may find it less critical but still benefit from consistency.

 

Reclamation log reference number
Recommendation: Marking this field as mandatory ensures each log has a unique, traceable identifier that can be referenced in dispatch manifests, partner communications, and internal tracking systems. Without a reference number, linking this record to external documentation becomes significantly more difficult. Form administrators should confirm that the reference numbering convention is clearly communicated to users to avoid inconsistent entries.

 

Date this log was opened
Recommendation: Requiring the log opening date establishes a chronological anchor for the entire record. This supports timeline reconstruction, shift tracking, and audit sequencing. It is a low-effort field that provides high operational value, and requiring it is proportionate to the form's record-keeping purpose.

 

Total number of packs in this batch
Recommendation: Requiring the batch quantity provides a scope check against the detailed inventory table and downstream dispatch records. It helps ensure that no packs are omitted from the log and supports mass-balance reconciliation later in the process. The necessity of this field is closely tied to the form's material tracking objectives.

 

Primary reason the packs are being decommissioned
Recommendation: Requiring the decommissioning reason categorises the trigger event and supports downstream decision-making (e.g., routing experimental packs differently from field returns). The conditional follow-ups allow additional detail only when warranted, keeping the mandatory requirement proportionate. This field is operationally important for trend analysis and process improvement.

 

Battery pack serial or part number (first pack in batch)
Recommendation: Requiring at least the first pack serial number ensures that the batch can be identified at the unit level. Combined with the module serial range and inventory table fields, it supports precise traceability. This is a core data point for any reclamation record and requiring it is consistent with the form's traceability objectives.

 

Are all serial identifiers and labels legible?
Recommendation: Requiring this yes/no check surfaces traceability gaps early, before disassembly may further damage labels. The conditional follow-up for illegible labels captures the specific issue. Making this mandatory supports data quality by ensuring that label condition is assessed and documented for every batch, which may be important for later verification.

 

Person completing this identification section
Recommendation: Requiring the identifier's name establishes accountability for the data entered in Section 1. This supports quality assurance and provides a point of contact for follow-up queries. Whether full legal names or employee IDs are appropriate depends on the organization's internal record-keeping practices.

 

Rated pack capacity (Ah)
Recommendation: Requiring the rated capacity ensures that the state-of-health calculation has its denominator available. Without this value, the SOH formula provided in the form cannot be applied. This is a proportionate requirement given the form's explicit inclusion of a reference calculation.

 

Dominant cell chemistry
Recommendation: Requiring the cell chemistry classification supports downstream handling, recycling stream allocation, and material recovery planning. Different chemistries may require different disassembly precautions and recycling pathways. The conditional follow-ups for next-generation, mixed, and unknown chemistries ensure that edge cases are described. The necessity of this field depends on the organization's downstream processing requirements.

 

Are any cells visibly swollen, leaking, vented, or discoloured?
Recommendation: Requiring this visual condition check ensures that physical defects are assessed and documented before disassembly begins. Swollen or leaking cells may indicate elevated safety risks that influence handling precautions. The conditional follow-up captures the specifics of any affected units. Making this mandatory supports both safety documentation and data completeness.

 

Which isolation and preparation steps were completed before opening the pack?
Recommendation: Requiring this checklist ensures that critical pre-disassembly safety steps are documented for every batch. The structured multiple-choice format makes it easy for respondents to indicate which steps were completed and which were not. This supports consistent safety practice recording and makes gaps visible. The necessity of requiring all listed steps may depend on the organization's specific safety procedures.

 

Did any spill, leak, or uncontrolled release occur during disassembly?
Recommendation: Requiring this incident check ensures that environmental and safety events are captured and described. The conditional follow-up prompts detailed documentation when a release occurs. Making this mandatory supports incident tracking and may be important for the organization's internal environmental monitoring practices. The specific reporting obligations vary by jurisdiction and organizational policy.

 

I confirm that the steps recorded above reflect the work as actually performed, including any deviations.
Recommendation: Requiring this attestation checkbox reinforces the accuracy of the disassembly step log. It encourages respondents to record deviations rather than idealised entries. This is a proportionate requirement that supports data integrity without adding significant user effort.

 

Primary downstream partner or processor name
Recommendation: Requiring the partner name ensures that the receiving organisation is identified for every batch. This is a core traceability field for the reclamation chain and supports chain-of-custody documentation. Without it, linking the batch to its downstream processing route becomes difficult.

 

Did the partner provide written acceptance and processing documentation?
Recommendation: Requiring this yes/no check ensures that documentation gaps are surfaced and tracked. The conditional follow-ups prompt either file upload or explanation of the gap. Making this mandatory supports the form's documentation completeness objectives and helps identify batches that may need follow-up with the partner.

 

Do any residual hazards remain in the work area or in stored material?
Recommendation: Requiring this check ensures that open hazards are documented before the site is released. The conditional follow-up captures the nature, location, and controls for each residual hazard. This is a proportionate safety documentation requirement that supports handover to the next team or shift.

 

EHS reviewer name
Recommendation: Requiring the reviewer's name establishes clear accountability for the EHS clearance decision. This is a standard record-keeping practice for sign-off sections and supports traceability of the review process.

 

Role or title of the reviewer
Recommendation: Requiring the reviewer's role provides context for the clearance decision and helps verify that the review was performed by an appropriately positioned individual. The specific role requirements depend on the organization's internal delegation of authority.

 

Plant manager or accountable supervisor name
Recommendation: Requiring the supervisor's name adds a second layer of accountability to the clearance, reflecting a supervisory review step. This supports the form's goal of documenting a complete review chain. Whether this field is always necessary depends on the organization's sign-off procedures.

 

Reviewer signature
Recommendation: Requiring a signature formalises the clearance and provides a verifiable record of the reviewer's approval. This is a standard practice for operational sign-offs and supports the integrity of the log as a completed record.

 

Date of sign-off
Recommendation: Requiring the sign-off date timestamps the clearance decision and anchors it within the overall log timeline. This is a low-effort field with clear record-keeping value.

 

I confirm that this log is a complete and accurate record of the reclamation activity described, to the best of my knowledge.
Recommendation: Requiring this final attestation checkbox reinforces the overall integrity of the log and encourages thorough completion of all sections. It serves as a closing quality checkpoint before the record is filed.

 

Overall Mandatory Field Strategy Recommendation

The form employs a thoughtful mandatory field strategy, with required fields concentrated in three areas: traceability anchors (facility name, log reference, serial numbers, batch quantity), safety-critical checks (cell condition, spill incidents, isolation steps, residual hazards), and accountability sign-offs (reviewer identity, signature, attestations). This distribution is proportionate to the form's operational purpose and avoids overburdening respondents with excessive required fields in informational or supplementary areas.

 

Balancing data collection depth against completion rates: The form is substantial in length, spanning five detailed sections. While the mandatory fields are well-chosen, the overall form length may present a completion challenge during busy plant operations. Consider whether the form could be completed in stages (e.g., Section 1 at intake, Sections 2–3 during disassembly, Sections 4–5 at dispatch and clearance) to reduce the per-session burden on any single respondent.

 

Conditional logic: The form already makes effective use of conditional follow-ups for single-choice and yes/no fields. Consider extending this principle to some currently optional fields—for example, the module serial range field could be conditionally prompted when the batch size exceeds a certain threshold, or the electrolyte recovery volume could be prompted only when the electrolyte handling response indicates extraction or collection occurred.

 

Mandatory field placement and best practices: The mandatory fields are distributed across all five sections, which is appropriate given that each section serves a distinct operational purpose. The attestation checkboxes at the end of Sections 3 and 5 are well-placed as closing checkpoints. A general best practice is to ensure that mandatory fields appear early in each section so that respondents encounter them before optional supplementary fields, reducing the chance of incomplete submissions. In this form, the mandatory fields are reasonably well-positioned, though the Person completing this identification section field at the end of Section 1 could optionally be moved earlier if the organization prefers to capture accountability upfront.

 

Overarching observations: The form contains approximately 23 mandatory fields across five sections. This is a reasonable number given the form's comprehensive scope and the importance of traceability and safety documentation in the battery reclamation context. The concentration of mandatory fields in Section 5 (EHS clearance) is appropriate, as this section serves as the formal closing checkpoint. Organizations should periodically review the mandatory field set based on user feedback and operational experience to ensure that the required data remains aligned with actual processing needs without creating unnecessary barriers to completion.

 

To configure an element, select it on the form.

To add a new question or element, click the Question & Element button in the vertical toolbar on the left.