Coating Adhesion Testing Form: Assess Bond Strength Between Coating and Substrate

1. General Information and Test Identification

Use this record to document adhesion testing of a coating on a substrate. Complete each field as accurately as possible using the actual readings, settings, and observations from the test. This template is informational and general in nature; it does not replace any specific standard, procedure, or requirement that may apply to your work.

 

Sample ID/Specimen Number

Batch, Lot, or Job Number

Project or Work Order Reference

Test Date

Tester Name

Tester Role/Qualification Reference

Was a witness or second operator present during the test?

 

Witness name and role:

Laboratory/Facility Name

Sample Location or Area of Origin

2. Substrate Details

Describe the material beneath the coating. Substrate condition and preparation are often strong influences on measured adhesion, so record them carefully.

 

Substrate material type

 

Please specify the metal or alloy:

 

Please describe the existing coating system:

 

Please specify the substrate material:

Substrate Grade, Specification, or Thickness

Surface preparation method used before coating

 

Abrasive blast profile achieved:

 

Grit or abrasive type and grit size used:

 

Please describe the preparation performed:

Surface profile/roughness (if measured)

Was the surface cleaned and free of visible oil, dust, or moisture before coating?

 

Please describe the contamination or condition observed:

Substrate temperature at time of test (°C)

Substrate thickness at test point (mm)

3. Coating System Details

Record the coating applied to the substrate, including the number of layers, thickness, and cure status. These details help in interpreting adhesion results.

 

Coating type/chemistry

 

Please specify the coating type:

Coating Product Name or Manufacturer Code

Coating Colour/Finish

Number of coats applied

Coating Layer Details

Layer/Coat

Product or Description

Nominal Thickness (µm)

Measured Thickness (µm)

Application Date

A
B
C
D
E
1
Primer
 
60
62
2/10/2025
2
Intermediate
 
120
118
2/12/2025
3
Topcoat
 
60
57
2/15/2025
4
 
 
 
 
 
5
 
 
 
 
 
6
 
 
 
 
 
7
 
 
 
 
 
8
 
 
 
 
 
9
 
 
 
 
 
10
 
 
 
 
 

Total dry film thickness (µm)

Date coating was applied

Cure time elapsed before testing (days)

Curing condition

 

Please state the cure temperature and duration:

Was the coating applied under controlled environmental conditions (e.g. enclosed area)?

 

Please describe the controlled conditions:

4. Test Method and Standard Reference

Select the adhesion test method applied. If a published method or standard was followed, note its reference for traceability. Use of a reference is optional and depends on your organisation's practice.

 

Test method used

 

Dolly size used:

 

Please specify the dolly diameter:

 

Lattice spacing used:

 

Peel angle:

 

Please describe the test method used:

Method or Standard Reference (if followed)

Was the test procedure reviewed or approved before testing?

 

Reviewed/approved by:

Number of replicate tests performed on this sample

Test surface locations evaluated

 

Please describe the location:

5. Test Equipment and Calibration

Identify the instrument used and confirm its calibration status so results can be interpreted with confidence.

 

Test Equipment/Instrument Name or Model

Equipment Serial or Asset Number

Equipment Manufacturer

Measurement range of the instrument

Was the equipment calibrated or verified before the test?

 

Calibration/verification date:

 

Please explain why calibration or verification was not performed, and any known effect on the result:

Calibration due/next verification date

Calibration Certificate or Record Reference

Was an adhesive used to bond the test stub or dolly to the coating?

 

Please state the adhesive type, mixing ratio, and cure time used:

Ancillary equipment used

6. Test Conditions and Environment

Ambient and surface conditions at the time of test can affect readings. Record the actual measured values where available.

 

Ambient air temperature (°C)

Relative humidity (%)

Dew point (°C), if determined

Weather or site conditions

Test location

 

Please describe the test location:

Was the specimen conditioned (e.g. temperature or humidity soak) before testing?

 

Please describe the conditioning period and conditions:

Was the specimen exposed to any unusual condition before testing (e.g. salt spray, immersion, heat, chemical exposure, weathering)?

 

Please describe the exposure type and duration:

Loading rate applied during the test (e.g. MPa/s or mm/min)

Was the loading applied smoothly and continuously without shock or impact?

7. Measured Adhesion Strength Results

Enter the readings obtained. If you record results in several units, complete the fields you used and leave the rest blank.

 

Measured adhesion strength (MPa)

Measured adhesion strength (psi)

Measured adhesion strength (N/mm²)

Individual Test Readings

Test Point ID

Surface Location

Reading (MPa)

Failure Mode Observed

Within Acceptance?

A
B
C
D
E
1
T1
Centre of panel
6.2
Cohesive in coating
2
T2
25 mm from edge
5.4
Adhesive at interface
3
T3
Near weld
3.1
Adhesive at substrate
4
 
 
 
 
5
 
 
 
 
6
 
 
 
 
7
 
 
 
 
8
 
 
 
 
9
 
 
 
 
10
 
 
 
 

Average adhesion strength (MPa)

Lowest individual reading (MPa)

Highest individual reading (MPa)

Standard deviation of readings (MPa)

For qualitative tests (e.g. cross-cut or tape): overall rating observed

Did the reading stop increasing before failure of the substrate or test fixture?

 

Please explain what limited the reading (e.g. fixture capacity, substrate failure):

Additional observations or anomalies during testing

8. Failure Classification and Inspection

Classify where the failure occurred relative to the coating system. Accurate failure classification is central to interpreting an adhesion result.

 

Failure mode(s) observed (select all that apply)

 

Please describe the approximate proportion of each failure type observed:

Approximate percentage of adhesive (interface) failure on the tested area

Location of the weakest link identified

Were photographs taken of the failure surfaces?

 

Please upload the failure surface photographs:

Choose a file or drop it here
 

Please upload an image of the tested specimen or test area

Choose a file or drop it here

Was a microscopic or magnified examination performed?

 

Please summarise the magnified findings:

Surface defects noted on or around the tested area

Failure analysis notes and possible contributing factors

9. Acceptance Criteria and Result

State the criterion used to judge the result. Acceptance thresholds vary by product, project, and organisation; record the source of the criterion you applied.

 

Basis of the acceptance criterion applied

 

Specification or document reference:

 

Internal procedure reference:

 

Manufacturer document reference:

Minimum acceptable adhesion strength (MPa)

Is a minimum percentage of cohesive failure required by the criterion?

 

Required minimum cohesive failure (%):

Additional acceptance requirement (if any)

Test result

 

Please describe the condition of acceptance and who agreed it:

 

Please explain why the result is inconclusive and what is planned:

Was the measured value within the stated acceptance limit?

 

Margin above the limit (MPa):

 

Shortfall below the limit (MPa):

Does this result require retesting or additional sampling?

 

Please describe the retest plan and planned date:

Has a nonconformity or deviation record been raised for this result?

 

Nonconformity/deviation reference number:

10. Corrective Action and Follow-Up

If the result did not meet the criterion, record what action was taken or is planned. If the result was acceptable, you may skip this section or mark items as not applicable.

 

Was the surface or coating identified as a possible cause of a poor result?

 

What factor(s) were suspected? (select all that apply)

 

Please describe the suspected factor:

Corrective or preventive actions planned or completed

Target completion date for actions

Person responsible for follow-up action

Comments on effectiveness of action taken (complete after implementation)

11. Review, Approval, and Attachments

Confirm the record before release. Attach supporting documents such as calibration records, photographs, data sheets, and test certificates where available.

 

Please upload supporting documents (test data sheets, calibration records, data sheets, reports)

Choose a file or drop it here
 

Overall summary and conclusions

Limitations, uncertainties, or remarks on this test

Has this record been reviewed for completeness and accuracy?

 

Reviewed by (name and role):

Approver Name

Approval Date

I confirm that the information recorded reflects the observations and readings from the test performed.

Tester signature

Reviewer or approver signature

Report/Record Distribution Reference

Analysis for Coating Adhesion Testing Form — Bond Strength Assessment Record

Important Note:

This analysis provides strategic insights to help you get the most from your form's submission data for powerful follow-up actions and better outcomes.

AI-Generated Content: This template and its accompanying guidance are AI-generated to provide a practical starting point for your form-building needs. Please review and customise the content to ensure it is accurate, appropriate and suitable for your intended use.

This guide is provided for general informational and planning purposes only. It does not constitute professional, legal, financial, medical, employment, privacy, regulatory, or advice of any other kind, nor does it certify that this template is suitable or compliant for any particular jurisdiction or purpose.

Laws, regulations, industry practices and business requirements vary. You are responsible for reviewing and customising the template to suit your intended use and obtaining advice from appropriately qualified professionals where necessary.

Please delete this section before publishing your form. See our Terms of Service for further information.


 

Overview and Purpose

The Coating Adhesion Testing Form — Bond Strength Assessment Record is a comprehensive, well-structured template designed to document the bond strength between a coating and its underlying substrate. The form is organised into ten logically sequenced sections — general identification, substrate details, coating system details, test method, equipment and calibration, test conditions, measured results, failure classification, acceptance criteria, and corrective follow-up — which together mirror the natural workflow of an adhesion test from sample intake through to sign-off. This end-to-end structure is a significant strength: it encourages a complete and traceable record in a single pass, reducing the risk that critical contextual details are omitted or recorded elsewhere.

 

Section: General Information and Test Identification

This opening section establishes the identity and provenance of the test record. The introductory paragraph is a notable positive design choice — it sets expectations clearly, asks users to enter actual readings and observations, and transparently states that the template is general and informational rather than a substitute for any specific standard or procedure. That kind of honesty supports correct use of the form.

 

Sample ID/Specimen Number: Anchors the entire record to a unique specimen or test piece. A consistent sample identifier is fundamental to traceability and allows results to be matched to the physical sample, batch records, and any subsequent retests.

 

Batch, Lot, or Job Number and Project or Work Order Reference: Optional linking fields that connect the test result to production or project context. Keeping these optional is sensible, since not every test will be associated with a lot or work order.

 

Test Date: Establishes when the measurement was taken, supporting chronological record-keeping and helping interpret cure-time and environmental factors later in the form.

 

Tester Name and Tester Role/Qualification Reference: Identify who performed the test and, optionally, their role. Recording the operator supports accountability and makes it easier to investigate anomalies or replicate results.

 

Was a witness or second operator present during the test?: A well-designed yes/no question with a conditional follow-up. This provides an opportunity to document independent observation where required by local practice, without burdening users who tested alone.

 

Sample Location or Area of Origin: Free-text field for recording where the specimen originated. This is operationally useful when adhesion results vary across a structure or asset.

 

Section: Substrate Details

The section correctly emphasises that substrate condition and preparation are strong influences on measured adhesion. This framing helps users understand why the detail matters.

 

Substrate material type: A broad, practical single-choice list with conditional follow-ups for 'other metal or alloy', 'previously coated surface', and 'other'. This design balances quick selection with the ability to capture specifics only when needed — an efficient approach to structured data collection.

 

Substrate Grade, Specification, or Thickness: Optional detail that helps characterise the base material.

 

Surface preparation method used before coating: A comprehensive option set with conditional follow-ups that adapt to the chosen method (e.g. blast profile for abrasive cleaning, grit details for mechanical methods, free text for 'other'). This is one of the form's strongest examples of conditional logic — it gathers relevant depth without imposing unnecessary fields.

 

Surface profile/roughness (if measured): Numeric capture of surface texture where available, supporting later interpretation of results.

 

Was the surface cleaned and free of visible oil, dust, or moisture before coating?: A concise check with a negative follow-up to describe contamination. This is operationally valuable because surface contamination is commonly noted as a contributing factor in adhesion issues.

 

Substrate temperature at time of test (°C) and Substrate thickness at test point (mm): Useful numeric context fields for interpreting readings, particularly for pull-off and mechanical tests where substrate behaviour can limit the measurement.

 

Section: Coating System Details

This section captures the coating identity, build-up, and cure status — all factors that commonly influence adhesion interpretation.

 

Coating type/chemistry: A broad chemistry list with a conditional free-text field for 'other or unknown'. Covering common generic chemistries keeps the form brand-neutral and widely applicable.

 

Coating Product Name or Manufacturer Code, Coating Colour/Finish, and Number of coats applied: Straightforward identification and characterisation fields.

 

Coating Layer Details (table): A well-structured tabular capture of each layer with nominal and measured thickness, application date, and product description. Pre-populated example rows demonstrate expected data entry format, which improves data quality. This layer-by-layer detail is operationally valuable for diagnosing failures that occur between layers.

 

Total dry film thickness (µm), Date coating was applied, and Cure time elapsed before testing (days): Together these support interpretation of whether the coating had reached sufficient development before testing.

 

Curing condition: Useful option set with a follow-up for heat cure parameters. Documenting cure type and conditions helps explain results that may be cure-related.

 

Was the coating applied under controlled environmental conditions (e.g. enclosed area)?: Conditional follow-up to describe controlled conditions, contributing to understanding of application environment effects.

 

Section: Test Method and Standard Reference

This section does well to separate the test method from the equipment and conditions, keeping the record modular and easy to review.

 

Test method used: Covers the principal adhesion test approaches — pull-off, cross-cut, X-cut, peel, scratch, tensile/lap shear, and indirect tests — with method-specific follow-ups (dolly size, lattice spacing, peel angle, free text). This conditional branching is an effective design pattern: it collects method-relevant parameters without cluttering the form for users of other methods.

 

Method or Standard Reference (if followed): Optional traceability field. The introductory paragraph appropriately notes that use of a reference depends on organisational practice — a neutral, non-prescriptive framing.

 

Was the test procedure reviewed or approved before testing?: A simple yes/no check with conditional identification of the reviewer. This supports internal quality processes where pre-review is part of local practice.

 

Number of replicate tests performed on this sample: Supports understanding of result reliability and the basis for any statistical summaries entered later.

 

Test surface locations evaluated: A multiple-choice field allowing capture of diverse testing locations (edges, welds, repairs) where adhesion behaviour may differ.

 

Section: Test Equipment and Calibration

This section promotes confidence in the instrument used and its readiness at the time of test.

 

Test Equipment/Instrument Name or Model, Equipment Serial or Asset Number, and Equipment Manufacturer: Together these uniquely identify the instrument, enabling traceability back to calibration and maintenance records.

 

Measurement range of the instrument: Useful context — results obtained near the instrument's range limits may warrant different interpretation than mid-range readings.

 

Was the equipment calibrated or verified before the test?: A mandatory yes/no check with a mandatory date follow-up for 'yes', or an explanation follow-up for 'no'. This design records calibration status without presuming universal requirements — the form asks the user to state any known effect on the result where calibration was not performed.

 

Calibration due/next verification date and Calibration Certificate or Record Reference: Optional fields for ongoing calibration management and cross-referencing.

 

Was an adhesive used to bond the test stub or dolly to the coating?: The conditional follow-up requests adhesive type, mixing ratio, and cure time — a particularly thoughtful detail for pull-off testing, where adhesive performance can affect the outcome.

 

Ancillary equipment used: A multiple-choice list (profile gauge, thickness gauge, thermohygrometer, dew point meter, microscope, camera, cutting tools) that captures supporting instrumentation concisely.

 

Section: Test Conditions and Environment

The section introduces its purpose clearly — noting that ambient and surface conditions can affect readings — and asks for actual measured values where available.

 

Ambient air temperature (°C): Mandatory capture of the test environment temperature.

 

Relative humidity (%), Dew Point (°C), if determined, and Weather or site conditions: Optional environmental context fields, useful particularly for on-site testing where conditions are uncontrolled.

 

Test location: Categorises the testing environment (lab, workshop, field, confined area) with a conditional description for 'other'.

 

Was the specimen conditioned (e.g. temperature or humidity soak) before testing?: Conditional follow-up describing the conditioning period and conditions — relevant where pre-conditioning is part of local procedure.

 

Was the specimen exposed to any unusual condition before testing...?: Captures prior exposure history (salt spray, immersion, heat, chemicals, weathering), which may explain reduced adhesion observed.

 

Loading rate applied during the test and Was the loading applied smoothly and continuously without shock or impact?: These fields address testing technique, which can influence reported values. The second question is well phrased as a simple yes/no check.

 

Section: Measured Adhesion Strength Results

The results section is thoughtfully designed to accommodate both quantitative and qualitative tests.

 

Measured adhesion strength (MPa): Mandatory primary result field in a standard unit, with optional companion fields for psi and N/mm² — a practical multi-unit approach that respects different organisational conventions.

 

Individual Test Readings (table): Captures per-point data including test point ID, location, reading, observed failure mode, and acceptance checkbox. Pre-populated example rows illustrate expected entries and demonstrate how individual points can vary across a specimen.

 

Average adhesion strength (MPa), Lowest individual reading (MPa), Highest individual reading (MPa), and Standard deviation of readings (MPa): Summary statistics that help characterise spread and reliability of the readings.

 

For qualitative tests (e.g. cross-cut or tape): overall rating observed: A well-scaled qualitative rating with descriptive anchors, and an explicit 'not applicable — quantitative test performed' option that prevents irrelevant responses.

 

Did the reading stop increasing before failure of the substrate or test fixture?: A useful operational check, with a conditional follow-up explaining what limited the reading. This helps distinguish true adhesion failure from test-system limitations.

 

Additional observations or anomalies during testing: Free-text capture for observations that structured fields may not anticipate.

 

Section: Failure Classification and Inspection

Accurate failure classification is central to interpreting adhesion results, as this section rightly states.

 

Failure mode(s) observed (select all that apply): Comprehensive multiple-choice covering adhesive, cohesive, adhesive-layer, dolly-attachment, mixed, and no-failure outcomes, with a conditional description of proportions for mixed failures. This is a strong design for capturing complex, multi-mode failures.

 

Approximate percentage of adhesive (interface) failure on the tested area: A graded single-choice field that quantifies the interface-failure proportion efficiently.

 

Location of the weakest link identified: Concisely summarises where the failure initiated — helpful for root-cause analysis.

 

Were photographs taken of the failure surfaces? and Please upload an image of the tested specimen or test area: File and image upload fields support visual documentation. The image upload provides a direct way to attach specimen imagery.

 

Was a microscopic or magnified examination performed?: Conditional follow-up to summarise magnified findings.

 

Surface defects noted on or around the tested area: Multiple-choice covering common defect observations (blistering, cracking, peeling, pinholes, contamination, uneven thickness, discolouration) plus a 'no defects observed' option.

 

Failure analysis notes and possible contributing factors: Open-ended field encouraging thoughtful reflection on causes — appropriately phrased as possibilities rather than definitive conclusions.

 

Section: Acceptance Criteria and Result

This section correctly notes that acceptance thresholds vary and asks the user to record the source of the criterion applied. This avoids implying universal thresholds.

 

Basis of the acceptance criterion applied: Covers project specifications, internal procedures, manufacturer recommendations, industry practice, agreed limits, and 'no formal criterion available' — with conditional follow-ups to capture references. This is an effective way to document criterion provenance.

 

Minimum acceptable adhesion strength (MPa) and Is a minimum percentage of cohesive failure required by the criterion?: Optional fields capturing numeric and compositional thresholds where applicable.

 

Additional acceptance requirement (if any): Free-text for requirements not covered elsewhere.

 

Reference relationship between measured force and reported adhesion strength: A formula display (adhesion stress equals maximum force over area) adds a concise technical reference for users — a helpful inclusion as long as it is treated as illustrative context.

 

Test result: Mandatory classification of Pass, Fail, Conditional pass, or Inconclusive, with conditional follow-ups explaining conditions or retest needs. The 'conditional pass' option reflects real-world practice and is a thoughtful inclusion.

 

Was the measured value within the stated acceptance limit?: Conditional capture of the margin or shortfall relative to the limit.

 

Does this result require retesting or additional sampling? and Has a nonconformity or deviation record been raised for this result?: Forward-looking checks that capture follow-up and record cross-references.

 

Section: Corrective Action and Follow-Up

The section is appropriately conditional in intent — inviting users to skip it if the result was acceptable, which respects the reader's time.

 

Was the surface or coating identified as a possible cause of a poor result?: Yes/no gateway to a detailed suspected-factor multiple-choice list (preparation, contamination, thickness, cure, environment, product, substrate, method, operator). This structured branching efficiently captures root-cause context.

 

Corrective or preventive actions planned or completed: Practical action options plus a 'no action required' choice.

 

Target completion date for actions, Person responsible for follow-up action, and Comments on effectiveness of action taken: A clear accountability and effectiveness trail.

 

Section: Review, Approval, and Attachments

The closing section provides a sensible sign-off workflow with attachment options.

 

Please upload supporting documents (test data sheets, calibration records, data sheets, reports): Consolidates attachments in one place, improving record completeness.

 

Overall summary and conclusions and Limitations, uncertainties, or remarks on this test: Free-text fields that encourage balanced reporting — including recognition of limitations is good documentation practice.

 

Has this record been reviewed for completeness and accuracy?: Mandatory review confirmation with conditional identification of the reviewer.

 

Approver Name and Approval Date: Optional approval metadata.

 

I confirm that the information recorded reflects the observations and readings from the test performed.: A confirmation checkbox accompanying the signature fields.

 

Tester signature and Reviewer or approver signature: Signature fields supporting formal record sign-off.

 

Report/Record Distribution Reference: Optional field for tracking how the record was circulated.

 

Overall Summary

This form is a thorough, logically organised record template that covers the full lifecycle of a coating adhesion test — from sample and coating characterisation, through method and equipment documentation, to results, failure analysis, acceptance judgement, and follow-up. Its strengths include: clear section introductions explaining the purpose of each block; extensive conditional follow-ups that gather method-specific detail only when relevant; pre-populated example rows in tables that demonstrate expected data entry; balanced handling of quantitative and qualitative tests; and transparent framing of the template as informational rather than a replacement for specific standards. The multi-unit results fields and detailed failure-classification options reflect practical testing realities.

 

Areas that could further enhance usability include: the form is long, and testers completing it in the field may benefit from an abbreviated path for simple qualitative tests; some optional fields could be grouped or visually de-emphasised to reduce perceived length; and where several summary statistics (average, min, max, standard deviation) are manually entered, clear guidance or in-form calculation reminders could help avoid transcription inconsistencies. Overall, the form provides a strong foundation for consistent, traceable adhesion test documentation.

 

Mandatory Question Analysis for Coating Adhesion Testing Form — Bond Strength Assessment Record

Important Note:

This section explains why certain fields in this form are marked as required and provides general guidance on how these requirements may support the collection of complete, accurate and relevant information.

Required fields and information-collection obligations may vary depending on your industry, jurisdiction, business operations and intended use of the form. A field marked as required in this template does not necessarily mean that collecting the information is legally mandatory.

Please review each required field to determine whether it is necessary, appropriate and lawful for your particular purpose. Consider applicable privacy, data protection, consent and industry-specific requirements, and consult an appropriately qualified legal, privacy or compliance professional where necessary.

Please delete this section before publishing your form. See our Terms of Service for further information.

 

Individual Mandatory Field Analysis

Sample ID/Specimen Number
Recommendation: Requiring this field anchors the record to a specific test piece and supports reliable record-keeping across multiple tests and retests. A unique identifier reduces ambiguity when results are matched to physical samples or batch documentation. Form administrators should confirm that their identifier convention is clearly communicated to testers to avoid inconsistent entry formats.

 

Test Date
Recommendation: Requiring the test date supports chronological record-keeping and helps interpret cure-time and environmental variables captured elsewhere in the form. Its placement near the start of the form is practical and easy to complete. Whether a date field needs to capture the exact test date versus a broader testing period depends on the form creator's record-keeping needs.

 

Tester Name
Recommendation: Requiring the tester name supports accountability and makes it easier to follow up on anomalies or replicate results. It also pairs naturally with the optional qualification reference and signature fields. Organisations should decide whether a full name, employee ID, or both better suit their internal identification practices.

 

Substrate material type
Recommendation: Requiring the substrate material type ensures that every record includes basic context about the underlying material, which is generally relevant to interpreting adhesion results. The extensive option list with conditional 'specify' follow-ups keeps data structured while allowing specificity. Form administrators should review whether the option list reflects the substrate types they typically test and adjust wording to match their terminology.

 

Coating type/chemistry
Recommendation: Requiring the coating chemistry supports consistent categorisation of results and can help in later comparison across coating families. The conditional free-text follow-up for 'other or unknown' balances structure with flexibility. Whether a specific product name should also be required depends on the form creator's data-minimisation and reporting needs.

 

Test method used
Recommendation: Requiring the test method is central to interpreting any adhesion value — the same number carries different implications under different methods. The conditional follow-ups that capture method-specific parameters (dolly size, lattice spacing, peel angle) only when relevant are an efficient design that supports complete records without unnecessary burden. This requirement is well justified given the form's purpose.

 

Test Equipment/Instrument Name or Model
Recommendation: Requiring the instrument name or model supports traceability of the measurement to the equipment used, and works together with the optional serial number and calibration fields. This is proportionate to the form's technical documentation purpose. Form creators may wish to consider whether serial number should also be required where multiple identical instruments are in use.

 

Was the equipment calibrated or verified before the test?
Recommendation: Requiring this check supports interpretation of the result's reliability and prompts the tester to confirm instrument readiness. The design is well balanced — a 'yes' response requires a calibration date, while a 'no' response invites an explanation of any known effect. This avoids implying universal calibration requirements while still capturing the relevant status. Form administrators should confirm what level of calibration documentation their local practice expects.

 

Calibration/verification date (conditional follow-up)
Recommendation: Requiring the date when calibration or verification was confirmed ensures the follow-up is substantiated and supports later reference. Its conditional nature means it only appears when relevant, which is a proportionate use of required fields.

 

Ambient air temperature (°C)
Recommendation: Requiring the ambient temperature captures one of the most commonly recorded environmental variables and supports later interpretation of test results. It is a quick numeric entry with minimal friction. Form creators may wish to consider whether relative humidity should be equally required where humidity-sensitive coatings are commonly tested, though this depends on their operational context.

 

Measured adhesion strength (MPa)
Recommendation: Requiring the primary measured value in a standard unit ensures every record contains a quantified result (for quantitative tests) and provides a consistent data point for reporting and comparison. The optional psi and N/mm² companion fields accommodate different unit conventions without complicating the core requirement. For purely qualitative tests, form administrators might consider whether an alternative required entry (such as a qualitative rating) should be prompted instead.

 

Failure mode(s) observed (select all that apply)
Recommendation: Requiring failure classification ensures records capture not just how strong the bond was, but how it failed — which is central to interpreting an adhesion result. The broad option set, including 'no failure', accommodates all outcomes and reduces the risk of incomplete data. Form creators should confirm that the option list matches the failure terminology used in their procedures.

 

Basis of the acceptance criterion applied
Recommendation: Requiring the source of the acceptance criterion supports transparent, traceable judgement of results and avoids presenting thresholds without context. The conditional follow-ups capture document references only when applicable. This requirement is well proportioned — it asks for provenance rather than prescribing any specific threshold, which is appropriate given that criteria vary by product and organisation.

 

Test result
Recommendation: Requiring the outcome classification ensures every record concludes with a clear disposition — pass, fail, conditional pass, or inconclusive. The conditional follow-ups capture the reasoning for conditional or inconclusive outcomes, supporting accountability in decision-making. Form administrators should confirm that the four outcome categories align with their reporting and escalation processes.

 

Has this record been reviewed for completeness and accuracy?
Recommendation: Requiring a review confirmation supports quality assurance at the point of record completion and prompts a final check before the record is released. The conditional follow-up identifying the reviewer is a sensible complement. Whether this review step should be mandatory may depend on whether the form creator's process includes a formal review stage before record distribution.

 

Overall Mandatory Field Strategy Recommendation

The form currently marks approximately 14 fields as mandatory across its ten sections. The overall strategy is well balanced: mandatory fields are concentrated on core identification (sample ID, test date, tester name), essential technical descriptors (substrate type, coating type, test method, equipment), key environmental and measurement data (ambient temperature, measured adhesion strength), failure classification, and the concluding acceptance judgement and review check. This distribution ensures that every record contains the minimum viable dataset for interpreting an adhesion result, while leaving a large volume of supplementary context fields optional.

 
  • Balancing data depth against completion rates: The current ratio of mandatory to optional fields is reasonable for a technical laboratory record. However, the form is long overall, and testers completing it in the field may experience fatigue. Consider marking the remaining optional fields with a subtle visual distinction (for example, 'optional' markers or a lighter style) so that users can prioritise the required core data quickly.

  • Conditional logic as a completion aid: The form already uses conditional follow-ups extensively and effectively. Extending this pattern could further reduce perceived length — for example, showing the summary statistics block (average, min, max, standard deviation) only when more than one replicate reading is recorded, or showing the qualitative rating block only when a qualitative test method is selected. This would collect detailed information only when relevant.

  • Placement of mandatory fields: Mandatory items are sensibly distributed: identity fields at the top, technical descriptors in the middle sections, and the result and review checks near the end. This aligns with the natural completion workflow. One observation is that the mandatory Ambient air temperature field appears mid-form; if field completion speed is a concern, grouping all environmental data capture together with clear headings (as already done) helps maintain flow.

  • Review of requirement levels over time: Form administrators should periodically review whether each mandatory field remains necessary for their intended reporting and record-keeping use. If submission completeness issues arise, consider whether a field is truly needed on every record or whether it could be captured conditionally. Conversely, fields such as Relative humidity or Equipment Serial or Asset Number might warrant required status in contexts where instrument-specific traceability or environmental control is a priority.

  • Overall observation: The mandatory field strategy is proportionate and thoughtfully placed, supporting consistent, interpretable records without imposing unnecessary barriers. The combination of required core data with extensive optional context gives users flexibility while maintaining a reliable baseline dataset for each test.

 

To configure an element, select it on the form.

To add a new question or element, click the Question & Element button in the vertical toolbar on the left.