This form is used to record a documented readiness review before a concrete pour. It gathers observations about reinforcement, formwork, temporary supports, embedded items, access arrangements and pour planning so that the team can decide whether to proceed, proceed with conditions, or hold the pour for further work. Complete each section as fully as possible and attach supporting records where available.
The information captured here reflects a single inspection at a single point in time. Conditions can change between inspection and placement, so continued monitoring during the pour is recommended. This form does not replace project-specific procedures, design information or the judgement of competent personnel.
I understand that this form records inspection observations and does not by itself authorise any activity outside the project documents and procedures.
Enter the identifying details so this record can be traced to the correct project, location and pour.
Project name
Pre-pour inspection reference number
Site address or location description
Structure, element, zone or grid reference
Client or project owner organisation
Principal construction organisation
Specialist subcontractor for formwork and reinforcement
Date this inspection request was submitted
Proposed pour date
Proposed pour start time
Pour number or pour sequence identifier
Has this area been inspected previously and held pending further work?
Summarise the previous findings and what has been completed since:
This is recorded as the first readiness review for this area.
Describe what is being poured and how the concrete is expected to be placed. These details help the reviewer understand the level of scrutiny needed for formwork and temporary supports.
Which element types are included in this pour?
Slab or suspended floor
Beam or transfer structure
Column or pedestal
Wall or core
Foundation, footing or pile cap
Stair, ramp or landing
Raft or mat foundation
Precast or composite topping
Other:
Concrete strength class or grade specified
Design mix or batch plant mix reference
Estimated concrete volume for this pour (cubic metres)
How will the concrete be placed?
Concrete pump
Crane and skip or bucket
Conveyor
Direct discharge or chute
Tremie or drop chute into deep sections
Wheelbarrow or manual transport
Other
Has the pump setup, line routing and end hose restraint been reviewed for this pour?
Who reviewed the pump setup and when?
Consider arranging a review of the pump setup before placement begins.
Is the crane or lifting equipment current inspection documentation available on site?
Record the document or record reference:
What is the maximum free fall distance expected (metres)?
Expected placement rate (cubic metres per hour)
Expected total placement duration (hours)
Concrete supplier or batching plant
Delivery ticket or batch reference range
Ambient air temperature at time of inspection (degrees Celsius)
Concrete temperature at discharge, if known (degrees Celsius)
Workability or consistency test reference (slump, flow or equivalent)
Which constituents or additives are included in the mix?
General purpose cement
Supplementary cementitious materials (for example fly ash or slag)
Air entraining admixture
Water reducing or plasticising admixture
Retarding admixture
Accelerating admixture
Shrinkage reducing or compensating admixture
Steel or synthetic fibres
Pigment or colouring agent
None of the above
Other:
Are additional weather-related measures required for this pour (for example heating, cooling, sun protection or insulation)?
Describe the measures planned and who is responsible for them:
Record which project documents were used during this review. Where information is unclear or conflicting, note it in the observations area rather than assuming an interpretation.
Structural drawing numbers reviewed
Reinforcement drawing or bar bending schedule reference
Formwork or temporary works drawing reference
Concrete specification or project requirement reference
Method statement or work procedure reference
Risk assessment or task briefing reference
Are the drawings and documents used during this review the current revisions available on site?
How was the revision status confirmed?
Describe the document discrepancy and how it is being managed:
Has a temporary works or shoring design review been completed for the areas covered by this pour?
Who completed the design review and what is the record reference?
If a design review is normally expected for this type of temporary works, consider arranging one before placement.
Have any design changes, site queries or field revisions been issued since the last review of this area?
List the changes and how they have been incorporated:
Are previous inspection records for reinforcement, formwork or shoring available for this area?
Record the reference numbers of the previous inspection records:
Review the reinforcement against the project drawings and schedules. Where an item cannot be verified, record it as an observation rather than assuming it is correct.
What is the primary reinforcement type in this pour?
Deformed reinforcing bars
Plain reinforcing bars
Welded wire mesh or reinforcement mesh
Prefabricated reinforcement cages or assemblies
Combination of bars and mesh
Other:
Bar sizes and grades present
Is the reinforcement arrangement consistent with the current drawings and bar bending schedule?
Who verified the arrangement and how?
Describe the differences observed and any agreed corrective action:
Are bar spacing, member sizes and reinforcement quantities as indicated on the drawings?
Were spot measurements taken? Record typical values:
Are laps, couplers or mechanical connections correctly located and of the required length or type?
Record the connection type and typical lap length observed:
Describe the connection issues observed and the proposed corrective action:
What is the general surface condition of the reinforcement?
Clean and free of loose material
Light surface dust only
Surface rust staining with no loose flaking
Loose flaking rust or mill scale
Oil, grease or formwork release agent residue
Mud, soil or organic contamination
Other contamination
Describe the extent of loose rust or mill scale and any cleaning planned:
Describe the contamination and the cleaning method proposed:
Describe the contamination and the cleaning method proposed:
Are cover blocks, spacers and chairs of the correct size, type and spacing, and are they securely positioned?
What cover thickness is specified and what spacer types are used?
Describe the spacer or cover issues and the corrective action:
Typical measured concrete cover (millimetres)
Are starter bars, dowels and continuity bars correctly positioned, supported and protected from displacement during the pour?
How are the starter bars supported or protected?
Is the reinforcement arrangement sufficiently open for concrete flow and vibration around the bars?
Note any congested zones and how they will be addressed during placement:
Describe the congested areas and any agreed measures to reduce the risk of voids or honeycombing:
Have tie wire tails, offcuts, spacers, debris and standing water been removed from the formwork?
How was the area cleaned and when?
Are reinforcement test or material certificates available for the bars used in this pour?
Record the certificate or traceability reference:
Please rate the following reinforcement aspects based on what you observed:
Poor | Below expectations | Acceptable | Good | Very good | Not applicable or not observed | |
|---|---|---|---|---|---|---|
Reinforcement matches the current drawings and schedules | ||||||
Bar spacing and member dimensions are consistent with the design intent | ||||||
Laps, couplers and connections are correctly located | ||||||
Cover blocks and spacers are adequate and stable | ||||||
Reinforcement is clean and free of loose contamination | ||||||
Reinforcement is adequately supported and protected against movement |
Reinforcement Inspection Checklist
Check Item | Reference or Location | Source Document | Conforms | Observations | Record or Photo Reference | ||
|---|---|---|---|---|---|---|---|
A | B | C | D | E | F | ||
1 | Main bar size, grade and spacing | Level 4 slab, grid D2 to H7 | S-501 Rev D | Bottom mat N16 at 150 mm centres confirmed by spot measurement. | Photo P-1101 | ||
2 | Lap lengths and staggered splices | Grid C3 to E3 | S-501 Rev D, BBS-07 | Two laps found in the same section; bars to be re-located and staggered before pour. | Photo P-1102 | ||
3 | Cover blocks and spacer spacing | Bottom mat, zone 2 | Specification section 03 30 00 | Plastic wheel spacers at approximately 600 mm centres, cover measured at 30 to 33 mm. | Photo P-1103 | ||
4 | |||||||
5 | |||||||
6 | |||||||
7 | |||||||
8 | |||||||
9 | |||||||
10 |
Review the formwork for geometry, cleanliness, joint tightness, restraint and access. Note any areas where deflection or movement has been observed during previous placements.
What is the primary formwork system used for this pour?
Proprietary panel system
Traditional timber or plywood formwork
Aluminium panel system
Steel panel or fabricated mould
Table or flying form system
Tunnel or horizontal shuttering system
Slipform or jumpform
Stay-in-place permanent formwork
Other:
Is the formwork clean and free of debris, sawdust, standing water and leftover material?
How and when was the formwork cleaned?
Describe what remains in the formwork and the cleaning arrangements:
Has formwork release agent been applied correctly, with no contact with reinforcement or construction joints?
What release agent was used and how was it applied?
Describe the issue and the corrective action:
Are formwork joints tight and sealed to limit grout loss and leakage?
How were panel joints and corners treated?
Identify the joints or corners requiring attention:
Have line, level and plumb checks been completed and recorded?
Who completed the survey or dimensional check and what record was produced?
How would you describe the dimensional accuracy of the formwork against the project tolerances?
Comfortably within stated tolerances
Within tolerances but close to the limit
Marginally outside tolerance in isolated locations
Clearly outside tolerance
Not verified during this inspection
Record the locations and the measured deviations:
Record the locations, the measured deviations and the agreed corrective action:
Are ties, walers, strongbacks, soldiers and bracing installed and tightened as intended?
What tie system and spacing is used?
Are openings, blockouts, rebates, chamfers, waterstops and cast-in items correctly formed and secured?
List the blockouts or formed features verified:
Describe the missing or incorrect formed features and the corrective action:
Is there adequate access for placing, vibrating and inspecting the concrete within the formwork?
Describe the access arrangements provided:
Describe the access limitations and any changes planned:
Has any deflection, bulging or movement of the formwork been observed during recent activity or trial loading?
Describe what was observed and what action has been taken:
Is a formwork striking or removal sequence documented, including any reshoring arrangements?
Record the reference to the removal sequence or procedure:
Consider documenting a removal sequence before the pour so that expectations are clear for later stages.
Please rate the following formwork aspects based on what you observed:
Poor | Below expectations | Acceptable | Good | Very good | Not applicable or not observed | |
|---|---|---|---|---|---|---|
Formwork geometry, line and level match the project requirements | ||||||
Panels and surfaces are clean and properly prepared | ||||||
Joints, corners and edges are tight and well sealed | ||||||
Ties, walers and bracing are complete and secure | ||||||
Openings, blockouts and embedded items are correctly formed | ||||||
Access for placing and vibrating concrete is adequate |
Temporary supports carry fresh concrete, formwork, reinforcement, workers and equipment loads. Record the arrangement observed and any areas of uncertainty for follow-up by the responsible temporary works personnel.
What is the main shoring or propping system in use?
Adjustable steel props
System shoring or modular tower scaffolds
Timber posts and bearers
Raking shores or inclined braces
Combined shoring and access scaffold
Formwork table or flying form with integrated supports
Other:
Height from supporting surface to soffit or underside of formwork (metres)
Shoring design, duty class or load capacity reference
Are sole plates, base plates, sole boards or distribution beams in place and bearing on a sound surface?
Describe the bearing arrangement and the supporting surface:
Describe the inadequate bearing areas and the corrective action:
Are prop spacing, arrangement and vertical alignment consistent with the intended layout?
What prop spacing was observed and how was it verified?
Are horizontal bracing, diagonal ties, raking shores or lateral restraints installed and connected as intended?
Describe the bracing arrangement observed:
Are shoring assemblies tied into permanent structure or adjacent stable elements where required?
Describe the tie-in arrangement:
Has a competent person inspected the shoring and temporary works for this pour?
Record the inspector name, role and date of inspection:
Consider arranging a temporary works inspection before placement begins.
Is a reshoring plan in place for the period after the pour, including any load transfer requirements?
Summarise the reshoring approach and who is responsible:
Are there any surcharge loads on or adjacent to the shored area that could affect the temporary works (for example stacked materials, plant or traffic)?
Describe the surcharge loads and any control measures applied:
Shoring Zone Summary and Prop Count Check
Zone or Area Identifier | Area to be Shored (square metres) | Prop Spacing (metres) | Calculated Prop Count | Props Actually Installed | Variance (Installed minus Calculated) | Notes and Observations | ||
|---|---|---|---|---|---|---|---|---|
A | B | C | D | E | F | G | ||
1 | Zone A - Level 4 slab, grid D2 to F4 | 96.00 | 1.20 | 67 | 68 | 1 | Even layout observed, all props plumb and braced. | |
2 | Zone B - transfer beam soffit, grid F5 to H5 | 42.00 | 0.90 | 52 | 48 | -4 | Four additional props required near the mid-span; installation in progress. | |
3 | 0 | 0 | ||||||
4 | 0 | 0 | ||||||
5 | 0 | 0 | ||||||
6 | 0 | 0 | ||||||
7 | 0 | 0 | ||||||
8 | 0 | 0 | ||||||
9 | 0 | 0 | ||||||
10 | 0 | 0 |
Confirm that items to be cast into the concrete are present, correctly positioned and protected, and that the area has been set out accurately.
Are embedded services, conduits, pipes, sleeves and ducts installed and supported as intended?
Which services are included in this pour?
If services are expected in this pour, confirm whether their absence is intentional before placement.
Are waterstops, joint sealing strips or joint treatments installed at construction and movement joints?
Describe the waterstop or joint treatment type and location:
Are cast-in anchor channels, holding-down assemblies, ferrules, plates and inserts correctly positioned and secured?
Record the item references and how their positions were verified:
Describe the missing or misaligned items and the corrective action:
Have setting out, gridlines and level control points been verified for this pour?
Who verified the setting out and what record was produced?
Has a coordination or clash check been completed between reinforcement, formwork, embeds and services?
How was the coordination check carried out?
Describe any known coordination risks and how they will be managed during the pour:
Embedded Items and Blockouts Register
Item or System | Location or Grid Reference | Drawing Reference | Installed | Position Verified | Remarks | ||
|---|---|---|---|---|---|---|---|
A | B | C | D | E | F | ||
1 | Electrical conduit bank | Level 4 slab, grid E4 | E-201 Rev B | Conduits capped and tied to the top reinforcement mat. | |||
2 | Anchor channel assembly | Grid G3 | S-310 Rev A | Position check pending; survey requested before pour. | |||
3 | |||||||
4 | |||||||
5 | |||||||
6 | |||||||
7 | |||||||
8 | |||||||
9 | |||||||
10 |
A tidy, well-organised work area supports both quality and safe working. Record the current state of the area and any actions required before placement begins.
Are access and egress routes to the pour area clear and suitable for the expected crew and equipment?
Describe the access arrangements:
Are edge protection, guardrails, covers and barriers in place around openings, leading edges and changes in level?
Who checked the edge protection and when?
Describe the areas requiring attention and the corrective action:
Is lighting adequate for the expected pour duration, including any night or low-light working?
Describe the lighting arrangements:
Have the crew been briefed on the pour sequence, hazards and control measures?
Record the briefing reference and date:
Are exclusion zones, restricted areas and traffic management arrangements established where needed?
Describe the zone arrangements:
Are concrete washout, waste handling and spill response arrangements in place?
Describe the washout and spill arrangements:
Which potential hazards have been identified for this pour?
Working at height
Manual handling of reinforcement or formwork components
Wet concrete skin contact or splashing
Moving plant, pump lines or crane operations
Vibration exposure
Restricted or confined access
Slips, trips and uneven surfaces
Noise
Adverse weather exposure
None identified beyond routine activity
Other:
Are emergency communication arrangements and first aid provisions available in the pour area?
Describe the arrangements:
Weather can influence placement, finishing and early-age behaviour of concrete. Record the conditions at the time of inspection and the forecast for the planned pour window.
What were the weather conditions at the time of inspection?
Clear and dry
Overcast and dry
Light rain
Heavy rain
Strong wind
High heat or direct sun
Cold or near freezing
Fog or low visibility
Other
Describe the rainfall conditions and any protective measures planned:
Describe the heat conditions and any protective measures planned:
Describe the cold conditions and any protective measures planned:
Wind speed at the time of inspection (kilometres per hour)
Is rain forecast during the planned pour window?
Describe the contingency arrangements for wet weather:
Are drainage and runoff controls in place to prevent water entering the formwork or affecting the supporting surface?
Describe the drainage and runoff controls:
Is this planned as a night pour or a pour outside normal working hours?
Describe the additional arrangements for out-of-hours working:
Record the intended approach to placement, compaction, sampling and curing so that the team shares a common understanding before work starts.
Is the pour sequence documented so that placement can proceed continuously and in the intended order?
Record the pour sequence reference:
Describe the planned order of placement and any risk of interruption:
Which compaction or consolidation methods are planned?
Internal poker or needle vibrator
External or formwork vibrator
Self-compacting concrete without mechanical vibration
Manual rodding or tamping
Combination of methods
Other:
Are sufficient vibrators available, including at least one spare, and are they in working order?
How many vibrators are available and who checked them?
Consider arranging additional equipment before placement begins.
Is a sampling and testing plan in place for fresh and hardened concrete?
Summarise the sampling plan, including sample frequency and who will collect the samples:
If testing is expected for this pour, consider confirming the sampling arrangements with the relevant project personnel.
Planned number of sample sets for this pour
Which curing methods are planned after placement?
Curing compound
Wet hessian, burlap or absorbent fabric
Plastic sheeting or membrane
Water ponding or continuous wetting
Insulated or protective blankets
Formwork left in place for an extended period
Not yet determined
Other:
Are finishing requirements for this pour defined (for example level tolerance, surface texture, floating or trowelling)?
Describe the finishing requirement:
Are measures in place to reduce the risk of cold joints or unplanned interruptions?
Describe the measures and any contingency arrangements:
Is post-pour monitoring planned (for example early-age temperature, movement, deflection or strength gain observations)?
Describe the monitoring approach and who will record the results:
Planned Pour Sequence and Volume Estimate
Sequence Number | Element or Zone | Planned Start | Planned Finish | Estimated Volume (cubic metres) | Placement Method | ||
|---|---|---|---|---|---|---|---|
A | B | C | D | E | F | ||
1 | |||||||
2 | |||||||
3 | |||||||
4 | |||||||
5 | |||||||
6 | |||||||
7 | |||||||
8 | |||||||
9 | |||||||
10 |
Record any items that require attention before or during the pour. Descriptions should be specific enough for another person to locate and understand the issue.
Were any non-conformances, defects or deviations observed during this inspection?
Provide an overall summary of the findings and the general corrective approach:
No items were recorded at the time of inspection. Continue to monitor conditions up to and during placement.
Rectification and Follow-Up Log
Item Number | Description of Observation | Location or Element | Raised By | Target Rectification Date | Rectified | Date Closed | ||
|---|---|---|---|---|---|---|---|---|
A | B | C | D | E | F | G | ||
1 | ||||||||
2 | ||||||||
3 | ||||||||
4 | ||||||||
5 | ||||||||
6 | ||||||||
7 | ||||||||
8 | ||||||||
9 | ||||||||
10 |
Additional comments, photographs or supporting records to be attached
Select the outcome that best reflects the current state of the work area. Where the outcome is conditional, list the conditions clearly so they can be checked before placement begins.
What is the outcome of this pre-pour inspection?
Ready to proceed with the pour
Ready to proceed subject to listed conditions
Hold the pour pending rectification and re-inspection
Further review or design input required before a decision
List the conditions that must be satisfied before or during placement:
Describe what must be completed before re-inspection is requested:
Describe the input or clarification needed and who is being consulted:
Re-inspection date and time, if applicable
Limitations of this inspection or matters outside its scope
Overall confidence that the pour can proceed as planned (1 = very low, 10 = very high)
Record the people involved in the inspection. Each person confirms only what they personally reviewed or observed.
Lead inspector name
Lead inspector role or position
Date and time of inspection
Contractor or subcontractor representative name and role
Reinforcement foreperson name
Temporary works representative name and role
Client or consultant representative name and role, if present
I confirm that the observations recorded in this form reflect what I reviewed at the time and place stated.
I understand that conditions may change after this inspection and that further checks may be needed before and during placement.
I confirm that any follow-up items listed in this form have been communicated to the responsible persons.
Lead inspector signature
Contractor or subcontractor representative signature
Client or consultant representative signature, if applicable
Use this short final check shortly before concrete placement begins. It is intended to catch changes that may have occurred after the main inspection.
Has anything changed in the reinforcement, formwork or shoring since the main inspection was completed?
Describe the change and confirm whether it has been reviewed:
Are all listed rectification items either closed or accepted as conditions of the pour?
Record who confirmed the status of the rectification items:
Is the formwork and shoring area clear of loose materials, tools and debris at the time of placement?
Who carried out the final clean-down check?
Are the delivery, placement and testing arrangements confirmed and ready?
Record the confirmation details:
Name of the person completing this final check
Date and time of final check
Any last-minute notes or instructions for the pour team
Analysis for Pre-Pour Inspection Permit Form for Rebar, Shoring and Formwork
Important Note:
This analysis provides strategic insights to help you get the most from your form's submission data for powerful follow-up actions and better outcomes.
AI-Generated Content: This template and its accompanying guidance are AI-generated to provide a practical starting point for your form-building needs. Please review and customise the content to ensure it is accurate, appropriate and suitable for your intended use.
This guide is provided for general informational and planning purposes only. It does not constitute professional, legal, financial, medical, employment, privacy, regulatory, or advice of any other kind, nor does it certify that this template is suitable or compliant for any particular jurisdiction or purpose.
Laws, regulations, industry practices and business requirements vary. You are responsible for reviewing and customising the template to suit your intended use and obtaining advice from appropriately qualified professionals where necessary.
Please delete this section before publishing your form. See our Terms of Service for further information.
This Pre-Pour Inspection Permit Form is a comprehensive, well-structured data-capture instrument designed to record readiness observations before concrete placement. It covers reinforcement, formwork, shoring and temporary works, embedded items, access arrangements, weather conditions, placement planning, and rectification tracking. The form is organised into clearly delineated sections that follow a logical workflow—from identification through inspection, planning, and sign-off—making it intuitive for inspectors to navigate. A notable strength is the extensive use of conditional follow-up questions that adapt the form to the respondent's answers, reducing unnecessary fields while capturing relevant detail. The inclusion of structured tables with formula-driven calculations (such as prop count checks and volume estimates) adds operational value by supporting quantitative cross-referencing. The form also includes a final pre-placement check section, which is intended to capture changes that may occur after the main inspection. Overall, the form appears designed to support thorough documentation and structured decision-making, subject to the organisation's own procedures and qualified review.
The introductory section clearly explains the form's purpose: to record a documented readiness review before a concrete pour. It sets expectations that the form captures observations at a single point in time and does not replace project-specific procedures or competent judgement. The acknowledgment checkbox—I understand that this form records inspection observations and does not by itself authorise any activity outside the project documents and procedures—is a thoughtful design choice that may help establish shared understanding among respondents about the form's scope and limitations.
Project name — This field is intended to associate the inspection record with the correct project, supporting traceability and record organisation. Pre-pour inspection reference number — Provides a unique identifier that may help with filing, cross-referencing, and retrieval of this record among multiple inspections. Site address or location description — Captures the physical location, which is useful for multi-site or large-site projects where precise location context matters. Structure, element, zone or grid reference — Allows the form creator to document exactly which part of the structure is being reviewed, reducing ambiguity. Client or project owner organisation, Principal construction organisation, and Specialist subcontractor for formwork and reinforcement — These fields capture the organisational context and may help identify responsible parties for follow-up actions. Date this inspection request was submitted and Proposed pour date — Establish a timeline for the inspection and the planned activity. Proposed pour start time — Adds scheduling granularity. Pour number or pour sequence identifier — Helps place this pour within the overall construction sequence. Has this area been inspected previously and held pending further work? — This conditional question is an effective design choice: it prompts the respondent to document prior findings and completed remediation, or to confirm this is the first review, thereby building a continuity-of-records trail.
Which element types are included in this pour? — Captures the structural context, which is intended to inform the level of scrutiny needed. The follow-up for 'Other' allows flexibility. Concrete strength class or grade specified — Records the design requirement, supporting verification against project documents. Design mix or batch plant mix reference — Links the pour to a specific mix, aiding traceability. Estimated concrete volume for this pour (cubic metres) — Quantitative input that may help with logistics and delivery planning. How will the concrete be placed? — This single-choice question with method-specific follow-ups (pump setup review, crane inspection documentation, free-fall distance) is well-designed: it captures only the detail relevant to the chosen placement method. Expected placement rate, Expected total placement duration, Concrete supplier or batching plant, and Delivery ticket or batch reference range — These fields support logistics coordination and material traceability. Ambient air temperature and Concrete temperature at discharge — Capture environmental and material conditions at the time of inspection, which may be relevant for placement planning. Workability or consistency test reference — Records the reference to any quality testing performed. Which constituents or additives are included in the mix? — This multiple-choice question with an 'Other' follow-up provides a structured way to document mix composition. Are additional weather-related measures required for this pour? — A practical conditional question that prompts planning for environmental challenges.
Structural drawing numbers reviewed — Documents which design references were used, supporting auditability. Reinforcement drawing or bar bending schedule reference, Formwork or temporary works drawing reference, Concrete specification or project requirement reference, Method statement or work procedure reference, and Risk assessment or task briefing reference — These fields collectively build a document trail showing what information informed the inspection. Are the drawings and documents used during this review the current revisions available on site? — This conditional question is operationally valuable: it prompts verification of document currency and captures discrepancies when they exist. Has a temporary works or shoring design review been completed for the areas covered by this pour? — Records whether design review has occurred, with follow-ups for details or a prompt to arrange one. Have any design changes, site queries or field revisions been issued since the last review? — Captures changes that may affect the inspection scope. Are previous inspection records for reinforcement, formwork or shoring available for this area? — Supports continuity of records.
What is the primary reinforcement type in this pour? — Establishes the reinforcement context. Bar sizes and grades present — Records observed material specifications. Is the reinforcement arrangement consistent with the current drawings and bar bending schedule? — A key verification question with follow-ups for both conforming and non-conforming outcomes. Are bar spacing, member sizes and reinforcement quantities as indicated on the drawings? — Prompts dimensional verification. Are laps, couplers or mechanical connections correctly located and of the required length or type? — Captures connection quality with detailed follow-ups. What is the general surface condition of the reinforcement? — This single-choice question with contamination-specific follow-ups is well-structured for capturing surface condition observations. Are cover blocks, spacers and chairs of the correct size, type and spacing? — Verifies cover provision. Typical measured concrete cover (millimetres) — Quantitative measurement input. Are starter bars, dowels and continuity bars correctly positioned? — Checks projecting reinforcement. Is the reinforcement arrangement sufficiently open for concrete flow and vibration? — Addresses practical placement considerations. Have tie wire tails, offcuts, spacers, debris and standing water been removed? — Housekeeping check. Are reinforcement test or material certificates available? — Records traceability documentation. The matrix rating question and Reinforcement Inspection Checklist table provide structured summary views that may help reviewers quickly assess overall reinforcement readiness.
What is the primary formwork system used for this pour? — Establishes the formwork context. Is the formwork clean and free of debris? — Housekeeping verification. Has formwork release agent been applied correctly? — Checks preparation quality. Are formwork joints tight and sealed? — Addresses grout loss risk. Have line, level and plumb checks been completed? — Records dimensional verification. How would you describe the dimensional accuracy of the formwork against the project tolerances? — A graded assessment question with follow-ups for out-of-tolerance conditions. Are ties, walers, strongbacks, soldiers and bracing installed and tightened? — Checks restraint systems. Are openings, blockouts, rebates, chamfers, waterstops and cast-in items correctly formed? — Verifies formed features. Is there adequate access for placing, vibrating and inspecting? — Practical placement consideration. Has any deflection, bulging or movement been observed? — Monitors formwork stability. Is a formwork striking or removal sequence documented? — Forward-planning question. The matrix rating for formwork aspects provides a structured summary assessment.
What is the main shoring or propping system in use? — Establishes the support system context. Height from supporting surface to soffit — Dimensional input. Shoring design, duty class or load capacity reference — Links to design documentation. Are sole plates, base plates, sole boards or distribution beams in place? — Checks bearing arrangements. Are prop spacing, arrangement and vertical alignment consistent? — Verifies layout. Are horizontal bracing, diagonal ties, raking shores or lateral restraints installed? — Checks lateral stability provisions. Are shoring assemblies tied into permanent structure? — Verifies tie-in arrangements. Has a competent person inspected the shoring and temporary works? — Records inspection status. Is a reshoring plan in place? — Captures post-pour arrangements. Are there any surcharge loads on or adjacent to the shored area? — Identifies external influences. The Shoring Zone Summary and Prop Count Check table is particularly well-designed: it includes formula-driven columns for calculated prop count and variance, enabling quantitative cross-referencing between expected and installed props.
Are embedded services, conduits, pipes, sleeves and ducts installed and supported? — Verifies embedded items. Are waterstops, joint sealing strips or joint treatments installed? — Checks joint provisions. Are cast-in anchor channels, holding-down assemblies, ferrules, plates and inserts correctly positioned? — Verifies cast-in items. Have setting out, gridlines and level control points been verified? — Confirms dimensional control. Has a coordination or clash check been completed? — Prompts interdisciplinary verification. The Embedded Items and Blockouts Register table provides a structured register with installation and position verification checkboxes.
Are access and egress routes clear and suitable? — Checks access arrangements. Are edge protection, guardrails, covers and barriers in place? — Records perimeter protection status. Is lighting adequate? — Addresses visibility for the planned duration. Have the crew been briefed? — Records briefing status. Are exclusion zones and traffic management arrangements established? — Captures area management. Are concrete washout, waste handling and spill response arrangements in place? — Environmental considerations. Which potential hazards have been identified? — This multiple-choice question with an 'Other' follow-up provides a structured hazard identification prompt. Are emergency communication arrangements and first aid provisions available? — Records emergency readiness.
What were the weather conditions at the time of inspection? — This single-choice question with condition-specific follow-ups for rain, heat, and cold is well-designed for capturing environmental context. Wind speed at the time of inspection — Quantitative environmental input. Is rain forecast during the planned pour window? — Prompts contingency planning. Are drainage and runoff controls in place? — Checks water management. Is this planned as a night pour? — Captures out-of-hours working arrangements.
Is the pour sequence documented? — Records placement planning. Which compaction or consolidation methods are planned? — This multiple-choice question with method-specific follow-ups (vibrator availability check) is operationally useful. Is a sampling and testing plan in place? — Captures quality testing arrangements. Planned number of sample sets — Quantitative testing input. Which curing methods are planned? — Records post-placement care plans. Are finishing requirements defined? — Captures surface finish expectations. Are measures in place to reduce the risk of cold joints? — Addresses continuity planning. Is post-pour monitoring planned? — Records follow-up arrangements. The Planned Pour Sequence and Volume Estimate table with formula-driven totals supports quantitative planning.
Were any non-conformances, defects or deviations observed? — This conditional question captures overall findings with a summary follow-up. The Rectification and Follow-Up Log table is an effective tracking tool with columns for description, location, responsible party, target date, rectification status, and closure date, along with a formula-driven rectified total. Additional comments, photographs or supporting records to be attached — Provides a space for supplementary documentation references.
What is the outcome of this pre-pour inspection? — This mandatory single-choice question is the decision point of the form, offering four outcomes from 'ready to proceed' to 'further review required,' each with tailored follow-ups for conditions, rectification needs, or clarification requests. Re-inspection date and time — Schedules follow-up when needed. Limitations of this inspection or matters outside its scope — An important transparency field that may help document what was and was not reviewed. Overall confidence rating (1–10) — Provides a subjective confidence metric.
Lead inspector name, Lead inspector role or position, and Date and time of inspection — These mandatory fields establish who conducted the inspection and when. Contractor or subcontractor representative, Reinforcement foreperson, Temporary works representative, and Client or consultant representative — Capture the broader inspection team. The three declaration checkboxes (confirming observations reflect what was reviewed, acknowledging conditions may change, and confirming follow-up items were communicated) are well-crafted to establish shared understanding. The three signature fields provide a formal record of participation.
Has anything changed since the main inspection? — Captures last-minute changes. Are all listed rectification items closed or accepted? — Verifies rectification status. Is the formwork and shoring area clear? — Final housekeeping check. Are delivery, placement and testing arrangements confirmed? — Verifies logistical readiness. Name of the person completing this final check and Date and time of final check — Establish accountability for the final verification. Any last-minute notes or instructions — Provides a communication channel for the pour team.
This form demonstrates several notable strengths. Its logical section flow mirrors the actual inspection workflow, making it intuitive for field use. The extensive use of conditional follow-up questions is a standout design feature—respondents are prompted for additional detail only when relevant, reducing form length while capturing thorough information. The inclusion of structured tables with formula-driven calculations (prop count checks, volume totals, rectification counts) adds quantitative rigour. The form also includes thoughtful transparency features, such as the limitations field and the acknowledgment checkbox, which may help set appropriate expectations. The final pre-placement check section is a practical addition that addresses the gap between inspection and placement.
Areas that could be considered for refinement include the overall form length—while the comprehensiveness is a strength, it may present a significant completion burden, particularly for smaller pours. The form could benefit from a brief summary or dashboard view at the beginning or end that consolidates key findings. Additionally, the matrix rating questions, while useful for structured assessment, overlap somewhat with the detailed yes/no questions in the same sections; the form creator may wish to consider whether both are necessary for every inspection or whether the matrix could serve as a condensed alternative for routine pours. The placeholder examples throughout the form are a positive usability feature that may help respondents understand the expected level of detail.
Mandatory Question Analysis for Pre-Pour Inspection Permit Form for Rebar, Shoring and Formwork
Important Note:
This section explains why certain fields in this form are marked as required and provides general guidance on how these requirements may support the collection of complete, accurate and relevant information.
Required fields and information-collection obligations may vary depending on your industry, jurisdiction, business operations and intended use of the form. A field marked as required in this template does not necessarily mean that collecting the information is legally mandatory.
Please review each required field to determine whether it is necessary, appropriate and lawful for your particular purpose. Consider applicable privacy, data protection, consent and industry-specific requirements, and consult an appropriately qualified legal, privacy or compliance professional where necessary.
Please delete this section before publishing your form. See our Terms of Service for further information.
Question: Project name
Recommendation: Requiring this field helps ensure each inspection record can be associated with the correct project. In multi-project environments, this identifier may support record organisation, retrieval, and administrative processing. The form creator should confirm whether a free-text project name or a standardised project code better serves their filing and search needs.
Question: Structure, element, zone or grid reference
Recommendation: Marking this field as mandatory supports precise identification of the inspected area. This level of specificity is intended to reduce ambiguity when multiple pours or inspection zones exist within the same project. It may help reviewers and follow-up personnel locate the exact area referenced in the record.
Question: Date this inspection request was submitted
Recommendation: Requiring the submission date establishes a clear timeline entry for the inspection request. This date may help track the interval between request and inspection, and between inspection and planned pour. Whether this date must always match the inspection date depends on the form creator's workflow.
Question: Proposed pour date
Recommendation: Capturing the proposed pour date as mandatory supports scheduling and coordination. It allows the inspection record to be linked to a planned activity window and may help identify when an inspection record is approaching or has passed its intended use date. The form creator should consider whether this date should also trigger any notification or follow-up processes within their own systems.
Question: Concrete strength class or grade specified
Recommendation: Requiring the concrete strength class or grade helps document the design requirement against which the pour is being planned. This field is intended to support verification against project documents and may help reviewers confirm that the correct specification is being referenced. Its necessity depends on the form creator's documentation practices.
Question: Structural drawing numbers reviewed
Recommendation: Marking this field as mandatory supports document traceability. Recording which structural drawings were reviewed during the inspection may help establish what information informed the observations. This is particularly useful when multiple drawing revisions exist or when follow-up questions arise about the basis for the inspection findings.
Question: What is the outcome of this pre-pour inspection?
Recommendation: Requiring the outcome selection ensures that every completed inspection record includes a clear decision point. This field is intended to capture whether the area is ready to proceed, ready with conditions, on hold, or requires further review. The conditional follow-ups for each outcome prompt the respondent to document specific conditions or rectification needs, which may support subsequent processing and communication.
Question: Lead inspector name
Recommendation: Requiring the lead inspector's name establishes accountability for the inspection record. It allows the record to be associated with the individual who conducted the review and may help with follow-up queries. The form creator should confirm whether capturing a full name or a role-based identifier better aligns with their record-keeping practices.
Question: Lead inspector role or position
Recommendation: Marking the lead inspector's role as mandatory provides context about the level of review conducted. It may help users of the record understand the perspective from which the inspection was performed and supports organisational traceability. Whether the role must match a predefined list or can be free-text depends on the form creator's needs.
Question: Date and time of inspection
Recommendation: Requiring the inspection date and time establishes when the observations were made. Since the form notes that conditions can change between inspection and placement, a precise timestamp may help contextualise the record and support any subsequent review of timing.
Question: Name of the person completing this final check
Recommendation: Requiring this field in the final pre-placement check section establishes accountability for the last verification step. It may help identify who confirmed the area was ready shortly before placement began, which can be useful if questions arise about the state of the work area at that time.
Question: Date and time of final check
Recommendation: Marking the final check date and time as mandatory records when the last verification occurred relative to the planned pour start. This timestamp may help establish the recency of the final check and support coordination with delivery and placement schedules.
Balancing Data Depth and Completion Rates: This form contains 12 mandatory fields spread across identification, inspection outcome, and sign-off sections. The mandatory fields are concentrated in areas that establish core record identity (project, location, dates), decision outcomes, and accountability (inspector details). This distribution appears reasonable: the mandatory fields capture essential record metadata, while the extensive detail sections are largely optional or conditional. However, the overall form length is substantial, and the cumulative completion effort—including optional fields—may still present a significant burden. The form creator may wish to consider whether all sections are needed for every pour or whether a tiered approach (e.g., a shorter form for routine pours and the full form for complex or high-risk pours) could improve completion rates without sacrificing record quality.
Use of Conditional Logic: The form already makes extensive use of conditional follow-ups, which is a strength. This approach keeps the mandatory field count low while still capturing detailed information when relevant. The form creator may wish to explore whether additional sections could be made conditional—for example, the shoring and temporary works section might be abbreviated or expanded based on the element type selected, or the weather section could be tailored based on the proposed pour time.
Best Practices for Mandatory Field Selection: The current mandatory fields are well-chosen: they capture identity, timing, key specifications, decision outcomes, and accountability. These are the fields most likely to be needed for record retrieval, administrative processing, and follow-up. Optional fields that capture detailed observations, measurements, and supporting references appropriately allow inspectors to record as much or as little detail as the situation warrants. The form creator should periodically review whether any currently optional fields have become operationally important enough to warrant mandatory status, and conversely, whether any mandatory fields could be made optional without compromising record utility.
Placement and Number of Mandatory Fields: The mandatory fields are distributed across the beginning (identification), middle (specification and documents), and end (outcome and sign-off) of the form. This distribution may help guide respondents through the form by anchoring key entries at natural decision points. The total of 12 mandatory fields is proportionate for a form of this length and complexity. The form creator may wish to consider grouping the mandatory identification fields together at the start with a brief note explaining why they are required, which may help respondents understand the purpose and reduce perceived friction.
To configure an element, select it on the form.